Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by roshan2

  1. R

    Help me with the filter response

    Hey i had designed a dual band filter and had got the following characteristics...what all can be wriiten in my thesis report with these simulation results..I will attach the results which i had obtained ---------- Post added at 04:30 ---------- Previous post was at 04:28 ---------- I...
  2. R

    help me with the matlab code..

    Hello Everyone Actually i am doing my project in developing a unit cell and i had done the simulation using ads and got the output characteristics of S11 S12.And after that i fabricated the unit cell and connected to the network analyser and got the result and i saved the file in .s2p format...
  3. R

    Help me with the application for the filter

    hey i am working on a metamaterial filter structure and i had designed in such a way to work as a dual band filter.I am getting the frquencies as 1.09 GHz and 3.35 GHz.What are the applications i can put for it.Please reply
  4. R

    Please tell whether it is right

    hey enjunear...i have been optimising my layout for a long time but getting results like this...shall i forward you my layout.are you familiar with ads momentum since i am using that to build.If so just pass me your id so that i will send it.Hope you understand my state
  5. R

    Please tell whether it is right

    well enjunear....what i wanted is a band pass filter...so what do you think about the characteristics...well i need to fabricate the structure and have to compare with this result...Wat do you suggest.....actually i am workin on metamaterials.....do respond
  6. R

    Please tell whether it is right

    what if when compared to an ideal or a general filter
  7. R

    Please tell whether it is right

    well.. please dont joke my friend..Well this was the result i got when i simulated the filter structure...is the simulation result fine when compared to a filter chara...
  8. R

    Please tell whether it is right

    Well i had designed a metamaterial structure and i got the simulation result as follows Well is the characteristics good when compared to a filter.Actually i optimised the structure so much and finally arrived at this output.My application is to make the structure to behave as a...
  9. R

    Help me with the graph

    well i am working on the metamaterial structure and this is what i got when i simulated the structure in ads momentum and so you meant that the parasitic resonance occur at 3.94 Ghz..am i write...please explain...well wat all points i can add
  10. R

    Help me with the graph

    can you be more elaborate.. i meant i want to include it on my thesis...tats why
  11. R

    Help me with the graph

    well that i understood...but my doubt is when i write the report on the simulation result what all things i should write...please respond
  12. R

    Help me with the graph

    Hello everyone, i am doing a simulation and i got a characteristics for s11 as shown in the image Just tell me what all p oints i can write in the report from the graph..
  13. R

    Help me with the code

    Actually i am doing a matlab code to plot a graph.the dispersion graph.Beta - x axis and Frequency- Y axis i want to extend the X axis to the negative side ie.want negative values in the x axis. my code which showed result in the positive axis is as follows: beta=0:2; w=1:5; p=6.9; wL=3.03...
  14. R

    help me to interpret the result from the graphs shown below.

    Hello Actually i am doing a simulation of a CRLHTL( filter) in ADS and i want to know the interpretation from the simulation results.I am attaching the image,the S parameters(bar graph and the smith chart).Please help me in interpreting the figure

Part and Inventory Search

Back
Top