Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by Pavithra89

  1. P

    FPGA Virtex 6 System monitor question

    Thanks for quick reply. This is how my stimulus file looks like since I'm looking only for temperature monitoring. TIME TEMP 00000 61 20000 86
  2. P

    FPGA Virtex 6 System monitor question

    Hi I am new to system monitor. I want to know how to measure the temperature of FPGA. Im doing this only for simulation purpose. Ive a basic idea of doing this, about DRP interface, register file interface but I have a doubt in giving a stimulus file, like what has to be written in the analog...
  3. P

    CPLD clock generation question

    hi I need to generate a clock of M rise time and N fall time using coolrunner CPLD where M and N are inputs. I need a basic idea on how to do this. please guide me . regards
  4. P

    [SOLVED] About Xport configurable pins.. Please help :)

    Hi Thank you all for ur reply. It was actually very helpful. I tried sending data through CP1 pin but I didn't get it back to PC. Regards
  5. P

    [SOLVED] About Xport configurable pins.. Please help :)

    Hi all I m doing a project involving Xport basically its a Ethernet interface. I wanted to know what does configurable pins CP1,CP2 and CP3 do and how is it different from data_out and data_in pin on Xport.. I was asked to serially send data to a Ethernet interface card through a CPLD connected...
  6. P

    multiple inputs issue :] Need help :]

    @TrickyDicky thank u I got it... :] Regards
  7. P

    multiple inputs issue :] Need help :]

    Hi TrickyDicky Thank you for ur reply What is Register address? Im confused... Regards
  8. P

    multiple inputs issue :] Need help :]

    Hi edaboardians I need your help. Hope I get some solution.How to accept multiple inputs and latch them into registers? I'm using a 8051 micro-controller and FPGA connected to each other because of which I've got only some pins available to do some operations. Basically what I've to do is store...
  9. P

    How to access a particular row and column in a matrix using assembly programming.

    Hi I want to scan a particular matrix row and column which is stored in look up table using 8051 assembly programming.. Please guide me how to do this. I need a brief overview as how this can be done. :) Regards
  10. P

    [SOLVED] Serial communication through USB.

    Thank u :) - - - Updated - - - Ok Il start looking at google as to which variant to use.. Regards n thank u :) - - - Updated - - - Thanks alot Il take all your suggestion Regards
  11. P

    [SOLVED] Serial communication through USB.

    Hi Other than converters? Is there any way? Regards - - - Updated - - - Thanks for providing me link. It was very useful :) Regards
  12. P

    [SOLVED] Serial communication through USB.

    Hi all I need to establish a serial communication protocol to 8051 using USB. I have been successful in using rs232. Ive been searching on ingoogle to get some information but in vain.. :( Please let me know all possible ways to get this done. Suggest me any books regarding this. Any suggestions...
  13. P

    [SOLVED] 12 bit input using only 4 input line......

    Thanks that was the error!! corrected them now Im getting the output in hardware as well :) - - - Updated - - - I'm thankful to all who helped me Thanks alot! Regards
  14. P

    [SOLVED] 12 bit input using only 4 input line......

    @ imbichie Hi After continuously trying and some changes in the code I got simulation working right :D :D :D But getting xst error :[ sequential logic for node <data_reg> appears to be controlled by multiple clocks Regards

Part and Inventory Search

Back
Top