Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by mohd_ind00

  1. M

    MPC7410 flashing issue - my code is not downloading to flash

    28f640j3 codewarrior Dear All, I have used MPC7410 PPC in my design along with TSI107. My boot flash(28F640J3) is residing on RCS0# of TSI and the data flash(28F128J3) on RCS2# of TSI. SDRAM is interfaced to TSI_CS0#. Hence there is no direct SRAM on the MPC7410 data bus. Now i am trying to...
  2. M

    Problem in program downloading with ROM version for MPC860

    We have designed a board using MPC860 processor. On the Board we have two Numbers of 1MB x 16 bit RAM arranged as 1MB x 32 bit and two numbers of 4MB x 16 bit Flash(AM29LV641DH) arranged as 4MB x 32 bit We are using Code warrior 8.5 IDE for firmware development and Ethernet TAP Pro for...
  3. M

    How can I access I2C bus in VGA Port

    why i2c at vga port Hi All, I am trying to test VGA Connector of PC, in that i can not find any method to directly access the I2C lines in VGA. Is it possible to send some data on i2c lines using programming or not i don't. Please Help.. tnx Imran
  4. M

    vhdl module for printer port

    Hi again, If anybudy has implemented atleast generation of 'busy' & ACK signals, plz reply.
  5. M

    vhdl module for printer port

    i8255 vhdl code Hi every budy, Can any budy know or give me the VHDL code for printer side functionality. I am trying tough to implement the same specially sequencing the status signals. please help. tnx Imran
  6. M

    how do i initialize SMC in MPC860

    SMCs in MPC860 Hi, anybody if has done this coding plz help.... facing hard in SMC1 initialization in MPC860. regards Imran
  7. M

    how do i initialize SMC in MPC860

    Hi All, I have problem facing in initialization of SMC-UART module in MPC860, i can't able to communicate with rs232 driver. the code is written in assembly. I have also initialize the DPRAM section to access the SMC registers. The buffers for TX and RX are also initilized in DPRAM itself and...
  8. M

    MPC860 Initialization CS generation

    Hi all, does anybody know CS generation initialization for MPC860 gpcm module. regards Imran
  9. M

    Problem initialization GPCM in MPC860

    mpc860 gpcm Hi All, I have some problem in initialization the gpcm module for generating CSs. Below is brief summery of my prceedings. If any budy knows plz help..... 1. I am using Motorola MCP860 with Flash, SRAM, & other devices. 2. I am able execute the code before i initialize the gpcm...
  10. M

    motorola MC9S12DP256 CLK & POWER SECTION

    Hi All, With reference to the above, in data sheet it has given that XCLKS pin to pull down for external oscillator but in the PLL section it given reverse pl clarify, and if possible post reference design. regards
  11. M

    motorola MC9S12DP256 CLK & POWER SECTION

    motorola clk HI All, I am carriying design with microcontroller MC9S12DP256. There are some issues with CLOCK and Power section. Can anybody post the reference design for this Microcontroller. I am using Crystal oscillator, whethere to connect XTAL to GND or left unconnected in this case...
  12. M

    USB HID keyboard interface firmware

    usb hid set german key Dear All, I am trying to write a firmware to interface USB keyboard with SL811HS, i have some problems with it . EP1, address 1 has been assigned to Slave device and it is configured. I dont know how to receive the key "pressed" from the keyboard. ( what is the...
  13. M

    ---> ATMEGA128 Programmer Schematic

    avr programmer schematic I have schematics u can build u r own programmer, maI me Added after 16 minutes: my id shashaec@indiatimes.com
  14. M

    Altera cyclone FPGA clock enable issue in QuartusII software

    Hi All, I am using Altera cyclone device EP1C6Q240C7. I am able to program and implement the design and it is working. I have implemented the DPRAM in device and using CLK0 & CLK1 pins of FPGA as two seperate clock for DPRAM. But i analyze the clock is not getting enabled, b'coz Compilation...
  15. M

    problem in configuring cyclone FPGA

    Re: problem in configuring cyclone FPGA- Solved Hi Mr Davorin & all I solved the problem configuring cyclone FPGA, the thing is i was not getting supply to the PLL ckt. Now it is configured well after correcting the problem. Thanks for all who have replied and helped me a lot. thanks, regards

Part and Inventory Search

Top