Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Dear Dora
Thank you for your interest in my question, but I have a lot of trouble so I don't like use picaxe chip anymore, I hope you understand Thank you again for your time to watch my question and HAPPY NEW YEAR
Dear All
I use this code( count by Button) for control direction of motor (picaxe 08m)
Because I don't know much about programming and rarely use it, I don't know how to set the value for Wx.Bx, hope you guys can help me fix the code. I want from 1st pulse to 10th pulse pin 1 is high and from...
Dear all,
I want to make a spot welder machine with a microwave transformer 800 E 120 vac 60 Hz ̣(my house use 120Vac 60Hz main power)
So to solder 2 pieces of metal (cut from food tin cans) about 0.30 mm thick. please advise me how many volts out and amps out minimum is need?
Hope you...
Thank you for taking the time to my question
My problem has been resolved. Thank you again so much for your enthusiasm to help me
Dear FvM
My problem has been resolved with your concern and help,Thanks again for your time help me
Dear All
I have follow this site https://www.facebook.com/MagLevitator/ for to make a magnet levitation, But not work (no volt out for
driver gate of mosfet ) So please help me check schema is right and if not good please correct it for work. Many thank you...
Dear All..
Please help me to know :
Can I use an electronic ballast 36 watt (120 vac 60 Hz) for my fluorescent lamp tube 15 watts with capacitor serial connection for current limit ?
//(output of ballast 36 watts drive wire >capacitor> my lamp tube 15 watts///
If yes please tell me value of...
Dear All.
I think with schema
(1)(Please see the photo) is easy for cascading 3 CD4017 ./ But just curious and like to lean more
So Please could you help me to know how to add and connection the circuit
(2)(Please see the photo) has worked for cascading 3 CD4017
.Thank you so much
Dear betwixt and FvM..
Thanks you and FvM and read more on Google now I understand slave and word address of 24c16 and timing scl +sda( but not sure 100%) . Tomorrow I will try write a code for Picaxe chip ( Do High Low wait Lopp ) 1hz ( for easy see led action if device working ) for driver...
Dear betwixt and FvM
First Thank you so much to both for your helpful. Almost in 24c16(e2) datasheet have not an example , so the newbie as me not easy understand for learning. Thanks your support now I understand . Could you help me again to know (give) the code
for WORD ADDRESS in mode...
Dear FvM and All..
As you know I have very low basic numeric and are learning .So please could you help me again get the The form code below: ( 1 or 0 )
*READ:
Start device select wire memory address REPEATED START device select...
Hi KlausST Thank you for your time reply.
Hi FvM No problem I will use anti bouncing by schmitt trigger circuit .Please just give me the code read write for 2 byte only Thank you
Hi Klaus and all..
Thank you for your ask. Sorry May be my question not clearing. I would
like to program just 2 byte (for easy start leaning) to 24cxx by manual ( by push button) like as video. but I don't know the code for read and write,
exp: X = 1 or 0 (Just for...
https://www.youtube.com/playlist?list=PL_4oazPiwX7MaGeF226lWEv24nfmSMk7A
Dear All..
I would like to learning program 24c16 or 24c256
like as this video on youtube (Please see). But my English is bad and have low basic numeric so I don't know much as him said and have read 24c16 data shell but...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
