Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by MI3talk

  1. M

    Need SMA connector without elbow design in HFSS

    Re: sma connector Are these file in touchstone/sNp format? Thanks! Added after 5 minutes: I just download the file and the .dsn file doesn't read. Can you load the correct one. Thanks!
  2. M

    Class A PA PAE with resistive load & inductor load

    Class A PA PAE with resistive load & inductor load quest -------------------------------------------------------------------------------- Hi all, I think I have a dumb question to ask. over couple of days, I was trying to understand why Resistive load Class A PAE is 25% and Class...
  3. M

    RF Design Engineer salary questions

    whats design engineer in arabic Hi, In my case, I don't have any publish paper, so I am kind of curious about if 2 yrs of intern could substitute into real industry experience as indicate on those job requirements. I heard sometimes company do not consider intern as real world experience...
  4. M

    RF Design Engineer salary questions

    rf design engineer salary would like to know what is the salary range for MSEE with 1 yrs of industry experience and close to 2 yrs of intern experience in Hillsboro, Oregon. With this experience, what do you think of the Job title? Electrical Engineer I, Electrical Engineer II, or EE III? I...
  5. M

    Any book about Low-Noise Amplifier design suggesting?

    I found "VLSI for Wireless Communication" by Bosco Leung is good to start with.
  6. M

    can anyone help me in this RF code?

    "real" is taking the real part of the argument "abs" is taking the magnitude of it. Z = R +jX, so abs(Z) is square root of (R^2 + X^2)
  7. M

    what is important in interview for electronic engineer??

    As I know, they will ask you what course work you had and project you done before, and whatever you put on your resume they will ask most of those. Usually the basics. Good luck!
  8. M

    series LC feedback network

    Hi all, Have a general question about series LC feedback network that connect between gate & drain of the FET. i am trying to have a good gain flatness in my amp from 50MHz to 2.6GHz within 1dB margin. Now my S21 @ 50MHz is 28dB, and gain @ 1.7GHz and 2.6GHz is around 19.5dB. Thanks!
  9. M

    Wideband CATV PA design

    Hi all, Questions regarding a CATV power amp design, Freq range: 50MHz to 3.0GHz S11 & S22 min spec = -15 to -15 thoughtout the range S21 min spec. 21dB over freq 2-stage design using pHEMT. Used tons of resistances to move it close to center with certain mismatch for S11(~-16dB across the...
  10. M

    [url]http://www.googlecashkey.com/index.htm[/url]

    www.googlecashkey.com dude, there is no free lunch, so don't touch it. It will get u into trouble. Hope that helps!
  11. M

    About Low power amplifiers design

    Re: About Low power design try this low power design book RF TECHNOLOGIES FOR LOW POWER WIRELESS COMMUNICATIONS Edited by TATSUO ITOH University of California—Los Angeles, California GEORGE HADDAD University of Michigan, Ann Arbor, Michigan JAMES HARVEY U.S. Army Research Office, Research...
  12. M

    High-Power GaAs FET Amplifiers ISBN-10: 0890064792

    Anyone knows how to get this book in pdf format? High-Power GaAs FET Amplifiers (Artech House Antennas and Propagation Library) (Hardcover) Hardcover: 388 pages Publisher: Artech House Publishers (December 1, 1993) Language: English ISBN-10: 0890064792 ISBN-13: 978-0890064795 Product...
  13. M

    PA design example in ADS

    I think you can go to ADS's Design Guide under Amplifiers, where they have many of PA design examples to practice on.
  14. M

    what is it ment by pCell??? thanks,

    I have a question with PCell in DW (Design Workshops) but not Cadence. Does anyone familiar with this software and how to write a PCell from it? Thanks!
  15. M

    How to be RF designer??? tips plz help

    I guess the best combination is to read the theory and try out ADS project in design guide to see how different parameters affects the whole circuit.
See more

Part and Inventory Search

Back
Top