Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by mathewsam2001

  1. M

    Fm radio pcba with usb/sd host connector & led 88:88

    Fm radio pcba with usb/sd host connector & led 88:88 (with remote) Can anyone please help me out in designing this FM radio with these features or help me out with the Block diagram and BOM Fm radio pcb with usb/sd host connector & led 88:88 (with remote) Features: a) Play the FM channels b)...
  2. M

    PCB Layout Job offer in Nodia

    PCB Layout Job Hi, Iam looking for exp pcb Layout guys for a startup in Noida. Allegro,orcad,HDL concept and Pads, tool knowledge is must Spetra quest or Hypelynx is value added. Regards, Sam Mathew Business Email : sam@swaytech.in Personal Email : mathewsam2001@gmail.com Skype Id ...
  3. M

    Urgent Requirement of PCB Designer

    Hi, Need one exp pcb designer for contract who can work in client site in Bangalore. The contract is for one month and might get extended. call me :- 9873665414
  4. M

    I need schematic for 40W and 60W Electonics Choke

    Electronic Choke Hi all ... I need schematic for 40W and 60W Electonics Choke....
  5. M

    I need schematic for 40W and 60W Electonics Choke

    +electronic +choke +schematic -lamp -control Hi all ... I need schematic for 40W and 60W Electonics Choke....
  6. M

    Need tutorial for Mentor Board Station

    Can anyone please help me out with the tutorial of Mentor Board Station Pcb Layout tool.
  7. M

    What is the Stitching Capacitor?

    Can any explain what is stitching capacitor??
  8. M

    How to decide PCB component placement ?

    PCB component placement ***Some Points to be consider at the time of Board Layout 1).All components should be placed with an appropriate functional group and their tracks routed within their designated PCB area. Arrangement of Functional Groups on PCB 2) Place ground plane(s) under all...
  9. M

    Problem with Allegro..(urgent)

    Run DB Doctor on the .dra and .brd file.
  10. M

    What are the back drilled vias?

    Re: Back drilled vias A back-drilled via is a normal through-hole via in a PCB that connects two signal layers, but the dangling stub hanging down from the last signal layer to the bottom of the board has literally been drilled out. A drill bit with a diameter a few mils larger than the drilled...
  11. M

    How to isolate a HART modem circuit from the 4-20 mA loops?

    Re: HART Thanks a lot sensor_ua... Can u send me the reference schematic for a HART modem to mathewsam2001 at gmail
  12. M

    Which software is good for PCB design for embedded systems and microcontrollers?

    Re: which is good ? Allegro ,Pads and cadstar windows verion are very much user friendly.
  13. M

    Guidelines for SIL2 and IS design

    Re: SIL Requirement Can any help me in this?
  14. M

    How to isolate a HART modem circuit from the 4-20 mA loops?

    Can anybody tell me how to isolate a HART modem circuit from the 4-20 mA loops.
  15. M

    Guidelines for SIL2 and IS design

    Hi , Can anyone help me out with the guidelines for SIL2 ( safety intergirity Level ) and IS ( Intrinsically safe ) design. The requirement is for designing FGP ( Fixed gas platform ) with SIL2 and IS approvals.
See more

Part and Inventory Search

Back
Top