Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by Manjunatha_hv

  1. M

    [SOLVED] Use *.prm files in AWR Microwave Office

    Hello, Yes you can import *.prm file into AWRDE MWO.... Just Right Click on Circuit Schematics & then select Import Netlist then choose the file type as All Files... Now choose the Netlist as PSICE (*.cir) file format... Then finally create new Circuit Schematic & add this model as...
  2. M

    Tsmc90 technology for sonnet

    Hi Happysky, See in Slide #8 of the below presentation on how to create tech file in sonnet... https://muehlhaus.com/wp-content/uploads/2011/06/SCD2011_Inductors_Transformers.pdf Also Sonnet can import the technology data from an existing cadence Assura "procfile"... ---manju---
  3. M

    Filter s2p file problem

    Hello Cem, Yes you are right...! But the system diagram to test this filter is not suitable & settings too not ideal for this filter test... I have created a new system diagram the"Filter Test" where I used simple RF Tone & the Filter... Then plotted the spectrum, & is working fine as...
  4. M

    Filter s2p file problem

    Hello Cem, Did you use LIN_S block for S2P file in AWR VSS? If not use this block it works... If so then upload ur VSS file *.emp & corresponding touchstone *.S2P file ---manju---
  5. M

    AWR/VSS radar design help?

    Hello Ilter, See the modified VSS file, it is much better especially the "Receiver_output 1" graph.... I just changed the Order of the filter implementations.... ---manju---
  6. M

    Measuring Input Voltage of a diode fed by an RF signal: MWO

    Hello, Add Vtime measurement to get the input voltage and also use the DC Node voltage annotations for the circuit schematic... ---manju---
  7. M

    AWR/VSS radar design help?

    Hello, Upload your AWR VSS file (*.emp) will try to help... ---manju---
  8. M

    DGS filter takes hour to simulate

    Re: DGS filter takes hours to simulate Try to set the coarse grid for the em simulations in AWR MWO-EMSight as it uses rectangular mesh... If you have AXIEM option, try using it as it is faster than EMSight... If you still have issues, upload MWO file (*.emp) here... ---manju---
  9. M

    [SOLVED] Tutorials for grounded CPW in Microwave Office

    Hello Max, let me know the results... Meanwhile for more info on CPW go through my post https://www.edaboard.com/threads/190845/#post986446 ---manju---
  10. M

    [SOLVED] Tutorials for grounded CPW in Microwave Office

    Hello Max, 1. Ferudun procedure is the generic one which can be used as starting point for CPW Circuit Schematics or EM Structure... 2. Just place the "CPW_SUB" substrate block & edit the parameters 3. Go through the Design Notes of following AWR examples... For Circuit Schematic & layout...
  11. M

    Drawing Airbridge in MWO

    Hello, upload ur MWO file *.emp, will try to suggest the solution... ---manju---
  12. M

    Drawing Airbridge in MWO

    Hello, It is very easy to construct Air Bridge in Planar em simulator especially in AWR AXIEM em editor... Just create the additional Air dielectric layer apart from the substrate layer & add the conductor metalization, & vias to connect the below metallization that completes the bridge...
  13. M

    Lange Coupler Designer with MWO, Designer and HFSS

    Hello, See my thread on lange coupler using AWR MWO with example file... https://www.edaboard.com/threads/49651/ Also an example from AWR **broken link removed** AWR Microwave Office is good for Lange coupler design & Optimization... MLANGE1 - EM quasi-static model (more accurate) for...
  14. M

    SCSwitch – Switch for SC analysis

    Hello, Did you setup all the parameters, including secondary parameters & connections for this element on the circuit schematic... Also this element work only in the APLAC simulator, so you choose that simulator when you create measurements.... ---manju---
  15. M

    [SOLVED] How To Model a Mixer in AWR ??

    Hello cmkrkmz, yes, you are correct MIXER_F is the spur table file based block & where as MIXER_B is the behavioral parameter based block... ---manju---
See more

Part and Inventory Search

Back
Top