Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
graupner mc-18 manual
Hi,
has anybody the schematics / pcb required for the Graupner MC-18 for interfacing to the PC (order no 4810.22)?
Thanks in advance,
Maddin
reflex xtr flight simulator
Hi to all reading those lines,
I'm looking for a schematic / PCB + firmware of a Reflex XTR flight simulator dongle, latest generation.
Can anybody please help`?
Thanks in advance,
Maddin
Hi all,
has anybody the schematics or PCB (with list of components :D) for the extension board required to connect a Graupner MC18 rc-control to PC?
I'm going to try myself as rc-heli pilot and would like to practise my new hobby on some PC simulator before crashing the heli after a 5 sec's try...
vhdl stack spartan 3
Sorry beeing a bit off topic, but I'm interested in buying a similar kit - maybe the same one :?:
Where did you buy your kit? Is it directly available from x!l!nx? How much does it cost?
Thanks in advance for your info,
Martin
Re: question on C
Storage required for type enum is compiler dependend; take e. g. the ra!sananc€ compiler and you will detect some selection about byte (char) or word (int) for enum type.
Re: Xilinx EDK 6.1 Bugs
jjljajp, that's true, but unfortunately you require an account to get access to the files :evil:
Is there any alternative source?
Thanks,
Maddin
Re: Xilinx EDK 6.1 Bugs
...looks like the same way of fixing M!cr0$0ft products :lol:
Anyway, has anybody EDK 6.1 servicepacks to share?
Thanks,
Maddin
Re: S0ft!ng ED!CCard2
Hi again,
ok, this question seems to be some unsolvable problem. :(
How does it look like about asking for information concerning interfacing to a car by using the diagnostic interface in general? Is there anything available that is some kind of "open source"?
Thanks...
S0ft!ng ED!CCard2
Hi all,
I'm looking for this or some similar schematics (or hardware) that is usable in combination with the VA$5163 tester s0ftware from S0ft!ng.
Does anybody know anything about it?
Thanks in advance,
Maddin
Hi all,
I've never heard about T-S parameters, but I think I wont get the same quality out of them like they were before in the original state.
Maybe I should really think about buying a new set...
Thanks to all who had gave some feedback,
regards,
Maddin
Re: data transmission
tulkas,
how frequent is it required for the data to be sent? Maybe it is possible to send the GPS data (already available on some bus? :lol: ) via e.g. some GSM modem / SMS ...
Hope it helped,
Maddin
Hi mkassem,
take a look at www.pcbpool.de and www.ats.net ; pcbpool is a good choice for prototyping boards, but I don't know whether it is a problem to get the material that suits best for your frequency range.
If board material is of special interest, take a look at AT&S ....
regards,
Maddin
Hi all,
I need some advice about loudspeakers since mine got destroyed by to much of the current/voltage product 8O
Anyway, since the speakers are quite old (Magnat Bull 203, not the Bull Power 203 which are used for car audio) I'm afraid not to get any original speakers, so can you give me...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.