Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I came across an error in PEX.
In LPE .tec file path to lvs rule file is given with Include directive.In LVS Rule file #DEFINE PEXRUN is uncommented for pexrun. Error encountered on conile .tec file
ERROR PEX5 in line 2762 in .tec file.
capacitance or resistance extraction layer not properly...
Hi
I am trying to do QRC with umc65nm.I am able to run QRC using Assura for the devices in library umc65ll EXCEPT FOR P_12_LLLVT.I am getting av_extracted file for all other transistors like N_12_LLLVT, N_12_LLHVT, P_12_LLHVT. Error popping up when I place P_12_LLLVT is ERROR-AVPXV-10019...
Hi
I am trying to do parasitci extraction using Assurs-QRC-> Run Assura using Quantus QRC. Technology is UMC 65nm.I am unable to figure out rule file to be laoded for it. I loaded UMC65/Rulefiles/QRC/LPE/Typ/* Can someoune help to solve the issue.
Hi
I have attached user defined library to existing technology librray- UMC.Component layouts are misaligned in my layout file...like vias are not properly
aligned..contacts misaligned in layout . If i open the layout view of that device in technology library it's proper.May I know how can I...
I wish to plot vco output power vs frequency.I executed pss.Then in Direct plot mainform pss is chosen, with in that power is chosen .In specify output resistance field i gave 50 ohm and selected the output differential nets to plot output power.I wish to know whether its the correct...
Hi
I wish to obtain plot HD3 vs Input power.I did PSS.I selected option power in mainform as shown in attachment.In the field to select harmonic I selected 3 rd harmonic and fundamental.Ploted in db Vs input power.Since Hd3=3Rd harmonic /Fundamenatl harmonic power.I subtracted fundamental...
I did PSS analysis and obtained power spectrum.3 RD order harmonic is obtained ,HD3=1/4(A3/A1) A3 AMPLITUDE OF 3rd order harmonic.A1,amplitude of fundamental.. How the harmonic amplitude can be plotted against input signal power,since in power spectrum its plotted against frequency.
I did PSS simulation,I can obtain total harmonic distrortion THD VS input power.But how to obtain HD3,third order harmonic distortion.It is different from IIP3 rite
Active inductor is a single port device.How can I connect the output port and do PSS analysis to obtain Total harmnic distortion Vs input power to characterise linearity.In the attachment I ahve shown the input port is connected and input impedance is found to be inductive.Since its a feedback...
I Have saved dc operating point of RF transistor save M0:all. After the dc sweep in print Dc operating point and dcop info in Result browser I can see instantaneous dc values of all parameters.But under dc in Result browser from which parameter can be sent to calculator or to plot window,I...
Thanks for your reply sir.I did it.I plotted iD and gm vs vgs .Then for X AXIS, using Y vs Y option ,I chose iD. Now I can plot gm vs ID .
Now I am stuck with another problem.My technology library is UMC180.When I use UMC_N_18_MM (MEDIUM MODE Transistor), I obtain all the Dc parameters like...
hi
I had gone through the above thread and the manual.In the manual how to obtain gm /id is explained.But how to set x axis to id is not mentioned.I can see in image(attached one as given in manual) as vs id.Is it possible to provide vs in calculator.I tried,but plot was not obtained.In the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
