Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by jimi84

  1. J

    Interface Pic with 16C654 quad UART

    I want three serial port in my system, at different baud rate for this I am using PIC18f452 with 16c654 (quad uart ic) i m having problem in initializing 16c654 . (bcz of too many register settings) can any one help me or share some code to initialize ths ic <JIMI>
  2. J

    need two serial port in one pic microcontroller .....

    I want three serial port in my system, at different baud rate for this I am using PIC18f452 with 16c654 (quad uart ic) i m having problem in initializing 16c654 . (bcz of too many register settings) can any one help me or share some code to initialize ths ic <JIMI>
  3. J

    Looking for source code for 16c554 and 8051

    I am using 16c654 can any one help me to initialize it ...
  4. J

    I am using BrushlessDc (BLDC) Motor with PIC 18fXX31

    Thnx Sootus But I wana know about its program code ... I hav some confusion that how to control it via controller .. there is a header file in my compiler C18 (pwm.h) but i am unable to use it .. <Jimi>
  5. J

    I am using BrushlessDc (BLDC) Motor with PIC 18fXX31

    I am using BLDC with optical encoder... I wana control it by using PIC 18FXX31 I had worked on PIC18FXX2 series but no idea about BLDC can any one guide me .. THNX <JIMI>
  6. J

    help with my project - GPS AND GSM\GPRS

    I m using gps lr9122 with pic 18f452 but i can not see any data transfer (not on PC neither on scope) :( Is there any starting configuration of this gps module My connections are:-- 1) My Antenna is connected to the 5V power supply (PIN 1) 2) GPS is being provided with 5V power supply (PIN...
  7. J

    Using PIC 18F452 with GPS LR9122

    1) I have left pin 5 floating 2) I m giving 5v from power supply.. 3) I think this can operate on both voltage level ... because data sheet says tht it can operate on both voltages +3.3VDC ~ +5.0VDC Power Input ftp://ftp.leadtek.com.tw/gps/9122/9122_v0.5_052807.pdf i hav also chkd the module...
  8. J

    Using PIC 18F452 with GPS LR9122

    I m using gps lr9122 with pic 18f452 but i can not see any data transfer (not on PC neither on scope) :( Is there any starting configuration of this gps module My connections are:-- 1) My Antenna is connected to the 5V power supply (PIN 1) 2) GPS is being provided with 5V power supply...
  9. J

    GPS and PIC16F877 serial transmission trouble

    I m using same gps lr9122 with pic 18f452 but i can not see any data transfer plz help me ..... Is there any starting configuration of this gps module
  10. J

    My experiments with PIC18F4550 <> USB

    Can u plz tell me about configration bits I m using Presto Programmer It only givs me option to check/uncheck required bit
See more

Part and Inventory Search

Back
Top