Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi winit_a
I want,too.
My project was taking a picture sending via GPRS,too.
or If it's posible, i wanna sending VDO,but now i looked at, i can send the picture.
Do you have the way to sending its?
Please copy to me at j_phetchuen at yahoo dot com.
I wanna finite project in this month? Thank...
Re: How to program for typing ascii between 2 station via si
Hi singhania12,
I saw your document and Thank you verymuch.
pls, recommended me, what the AT command, i will study?
I will try.
Very thank you again.
Naja
Hi K.somchok,
I am in thailand too.
I saw you in the topic of grps solution.
My project is using this too,i am using Sim300cz module.
Pls. give me the AT command of sending image via gprs
at j_phetchuen (at) yahoo dot com
and do you know how to connect gprs to gprs as realtime?
i want to...
Hello all,
How to using 1st sim300cz to 2nd sim300cz as connected realtime?
I have 2 computer + 2 sim300cz module.
I want to type ascii between two station (same the chat room).
I am not sure it's work?
Pls. give me an information and AT command using.
Thank you verymuch.
Naja
Hi all,
I am using MATLAB for calculate the value in vdo file,but i have some question.
1) Can using MATLAB for calculate the degree of the two axis?
meaning i have the two axis (<) i want to know the degree of them.
2) Can using MATLAB for calculate the expansion ratio in vdo file?
meaning i...
Hey raychen,
I have other problem in MATLAB,
I'm not sure you have any time for help me?
I have a problem of finding degree function in MATLAB.
I want to know the shifting degree of the box in the vdo file (vdo file to show a box on the conveyor).
In vdo a box put incorrect direction, i want to...
Hi Davy,
I'm not sure, your problem are the same of me.
I think you want to rotate the element, are not?
My job have a box on the conveyor but it put in the incorrect direction.
i want to use MATLAB to find the shifting degree of a box from the reference point
and i will sent this value to the...
Hi friend,
I have the box on the conveyor but some box are put incorrect direction.
I wanna rotation the incorrect box to the correct direction with MATLAB software,
to find the value of the shift direction degree and send this value to control servo motor.
I don't know MATLAB, Can do this...
How to reset Sim300cz
Hello friend,
I am using gprs modem (sim300cz)
I am not sure i setup some parameter later, now my sim300cz module cannot responding on hyperterminal.
How to reset sim300cz to factory default?
help me please
thank you
Naja
Re: matlab code for classification with neural network in ma
hi friend,
i want to help you but give me more information of your project
my understand of your " classification signature " is the comparative of two image, are not?
and what's your matlab version? i am using version "r2008b"
if...
Hello my friend,
I am using sim300cz connect to pc via com1(RS-232)
but now when i am type AT Command into the page it cannot show anything
i will try everytime and set every parameter but cannot work.
whom have more information of this problem?
i am attached .jpg file for my problem into...
help me,too!!!
I am using sim300cz,too. and i wanna sending image via gprs.
but i don't know at command,
emm,i see some forum of other website tell me to sending in gprs mode.
ohh, i don't understand. who have more description? pls. tell me too.
thank you.
Naja
pls. again.
thank you for the concept of communication between plc and website but
if i changing plc to microcontroller (ARM7) or X86 ATOM. how to programe its?
it use the same concept? or not and
who? have an example program or exanple project file to take this work,
Can you give me? thank...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.