Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by ilamseeker

  1. I

    Freescale MCF5213 _DMA Timer_PWM time period calculation problem

    Dear All, I am using two MCF5213 Evaluation kits: one for generating the PWM waveform and the other for checking the period of the generated PWM waveform. I am using he DMA timers to check the time period of the pulse. I have configured it but it is giving incorrect value in the...
  2. I

    Sensor - CAN BUS Interface Project

    Hi guys, I am doing a project in which i have to connect some sensors to a can bus. So, i need to have separate microcontrollers with each sensor which could read the sensor and put it on the can bus. Someone suggested me to use PIC microcontrollers for connecting each sensor to the CAN bus...
  3. I

    FPGA Interfacing with ADC0820

    Dear, I have some experience in Verilog and i think VHDL is somewhat similar. I am actually new to FPGA and ADCs. I need to know some help regarding implementation of the FPGA part (some idea about the possible implementation and interfacing with the ADC would help). Thanks Ali Tariq Nagi...
  4. I

    FPGA Interfacing with ADC0820

    Dears, I need to build Solar Tracking system. I am interfacing FPGA-Cyclone2 with ADC0820(datasheet attached). The ADC is intended to get voltage variations from the resistance in series with Cds photo resistor and forward the values to FPGA. LDR Circuit is attached. I am a totally newbie to...
  5. I

    Info about language dependent speech coders

    speech coding thanks...
  6. I

    What's the best Verilog program ?

    best verilog program dude google....
  7. I

    modem driver needed for USR 56k winmodem

    yes i did used the 3com56k.rpm but invain...i have mentioned my chipset manufacturer as USR
  8. I

    How to set Linux wireless interface?

    dear first check which chipset your wireless interface uses... this can be done by the command "lspci" u will c something like "communication controller etc" that line will give u the name of the chipset of that device.. den look for the drivers for that chipset... u shall also need kernel...
  9. I

    modem driver needed for USR 56k winmodem

    my modem driver model is 3cp5699a
  10. I

    modem driver needed for USR 56k winmodem

    my lspci output shows: communications controller: 3com corp, modem division USR 56k internal winmodem
  11. I

    matlab or C code needed for a speech encoding scheme

    pcm modulation c code hi all, i need very urgently matlab or C code for as many of the following speech encoding schemes: PCM DPCM ADPCM Delta Modulation linear prediction coding masking as in MPEG audio etc. if some one is have the related source codes,then plz let me knw at...
  12. I

    modem driver needed for USR 56k winmodem

    hi all, i searched the net a lot for an USR 56k winmodem which is on a PCI slot... plz if some knws where is can find or if some is have the pre-compiled or source code den do send it to me on iltafkhalid (attttttt) yahooooooooooooooooooooooo....
  13. I

    help needed::audio compression (DCT) using matlab

    audio compression matlab hi all, i have been given an assignment, to write matlab code for an audio file compression using DCT but using no inbuilt functions available in matlab. After taking DCT, i have to explicitly state and give reasons for how many samples have been sent for...
  14. I

    interfaching rs485 with atmega 128microcontroller

    rs485 atmega look in the attachments on this site...

Part and Inventory Search

Back
Top