Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by i_engineer

  1. I

    half wave voltage doubler using diode

    hi all, i want to make a half wave voltage doubler, at input side of rectifier is 9v ac can anybody please tell me what are equation/formula for find out proper value of capacitor thanks, i_engineer
  2. I

    433mhz Low noise Amplifier module RF

    Thanks goldsmith for quick reply any company make it,
  3. I

    433mhz Low noise Amplifier module RF

    Hi, Anybody knows where i can get LNA Module for RF 433 MHz i want only for receiver side Thanks
  4. I

    How to turn ON LCD Backlight

    Hi I am using LCD of Ketec, i don't know how to ON LCD Backlight ? datasheet link is below http://www.kentecdisplay.com/uploads/soft/Products_spec/FS-K70DWN0-V1-F-02_KED_.pdf Thanks
  5. I

    Artwork in cadance allegro pcb editor

    Hi , i want to create .art files(Gerber) files in allegro PCB editor, but when i select Manufacturer >> Artwork it shows like below instead of TOP,Bottom and other related layer name and also it can not create .art File so, please help me to solve this problem and make Gerber files Thanks
  6. I

    Gerber file in Orcad pcb designer

    Hi i have file with extension *.*.brd , i open it in Orcad pcb editor but now i want to make gerber file oftop and bottom layer, but i don't know how to create it, please anybody help me to create it Thanks
  7. I

    PADS manual link for beginner

    Hi, I'm new to PADS layout, Can anybody tell me link of best tutorial for Manually track routing, also how to open PADS layout file in Orcad 10 Thanks
  8. I

    [SOLVED] .pcb file can not open

    hi everyone ! i have download Literature TVP5158EVM Schematic and PCB Rev 1_2 from link,**broken link removed** and try to open a layout file name with EES-157-V1.2_Final.pcb from folder, but i cannot open it in OrCAD Layout plus or altium DXP can anybody guide me how to open it ,is there any...
  9. I

    [SOLVED] project options disabled in Altium DXP

    Hi Anybody can say me how to enble Project Options in Project menu of Altium DXP 2004 Schematic thanks Hiren
  10. I

    LPC2387 tutorial link

    Hell everyone, I'm new to learn nxp lpc2387 , can anybody tell me ,how to read manual of LPC micro controller for example, how can i use PINSEL0 function for LPC2387 for particular pins and please suggest me a good link for learn this, thanks
  11. I

    keil uvision3 ide guideline

    thanks ! can you guide me how to use define code generation tools in isis proteus for c thanks
  12. I

    keil uvision3 ide guideline

    hi bigdogguru ! i know how to simulate isis proteus with keil in asm language ,but don't about keil C please guide me how to use proteus's add/remove source files sub-menu of source menu for keil c language Thanks
  13. I

    keil uvision3 ide guideline

    Thanks to all ! it help me . i am using ISIS proteus 7 for simluation with keil ide can any one tell me how to use proteus's add/remove source files sub-menu of source menu for keil c language thanks
  14. I

    keil uvision3 ide guideline

    hi thannara123 this tutorial is describe only how to make a project and debug it ? i know that very well, i need complete tutorial of keil ide all menu & sub menu Thanks
  15. I

    keil uvision3 ide guideline

    Hi everybody ! i need keil uvision3 ide complete tutorial ,i.e. about guideline of ide all menu. Thanks !
See more

Part and Inventory Search

Back
Top