Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by hhhaithamhany

  1. H

    Flash memory of cisco switch "catalyst 2950"

    Hi all Please I erased the flash of the switch by mistake while configuring it and turn off the switch , is there any way to setup the IOS again or what should I do?? Thanks in advance
  2. H

    The difference between the RedHat and SUSE Linux.

    Re: Linux Help thank you all but now I am more confused because what I really want is to reach the administration level in Linux , especially in SUSE version but surprisely most of the courses based on redhat version so please if anyone has an advice to me don't hesitate to reply on me...
  3. H

    The difference between the RedHat and SUSE Linux.

    Re: Linux Help Thanks alot for your help, really it was nice information
  4. H

    The difference between the RedHat and SUSE Linux.

    Re: Linux Help Thank you very much for your reply but may i ask another two questions? 1)What is the difference between the courses? I mean if i take a course on fedora version then if i work on suse version it will be difficult? 2)what about ibm courses is it worth to take courses to reach...
  5. H

    The difference between the RedHat and SUSE Linux.

    Re: Linux Help first thank you for replying but i still confused about the difference in the offered courses in both version what i get from u now is that redhat is more general than suse as in redhat there is more codes and development, am i true? also there is another question why there are...
  6. H

    The difference between the RedHat and SUSE Linux.

    Hi all; Please I want to ask about the difference between the redhat version of Linux and SUSE Linux. If I take a course in any of them is there a great difference between versions or no? Please I need detailed information as much as possible. Thanks alot
  7. H

    How can I put random data as source in OrCAD?

    hi all how can i put random data as source in orcad?
  8. H

    Orcad library with opamp in the range of 1 MHz

    please if any one knows the name of a library in the orcad that contains opamps that can work on the range of 1 MHz please help me
  9. H

    clock and data recovery

    hi all, please i need help in designing the low pass filter that can be used in the clock and data recovery circuits. please if any know how to design it please help me. i use hogge phase detector and the loop is complete but there is no locking to the frequency of the input random data which...
  10. H

    Help me with designing a power meter (freq. KHz ~ MHz)

    Re: power meter Thank you very much for your help but is this circuit capable of measuring power over the required frquency range and is it capable of measuring the power for the CDMA system.
  11. H

    Help me with designing a power meter (freq. KHz ~ MHz)

    power meter hi all; I want to design a simple power meter that works on frequency range from few KHz to few MHz. Can anyone help me? thanks alot
  12. H

    Looking for monostable chip that works at 1.2 mega

    monostable please i want a monostable chip that works at 1.2 Mega
  13. H

    power meter using PIC

    please can anyone help me to make PIC program to be use in the power measurement
  14. H

    PLL4046a: inserting a pspice model

    74hc4046 spice Hiiiiiiiiiiiiiiiii again; first how can I insert a pspice model in the program itself second i want to use 74HC4046 instead of CD4046 but I still can't find the ic or the model redards; haitham
  15. H

    Looking for Orcad model of 74HC4046A

    74HC4046A model Hi alllllllll; this is my first post and I hope to get a fast reply Can any one help me to get a orcad model of 74HC4046A? thanks alot

Part and Inventory Search

Top