Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by helex

  1. H

    To Create Normally Closed Contact with Electronic components.

    Fail means both "false OFF" and "false ON". Any component of Control Circuit may be "Short" OR "Open" during failure.
  2. H

    To Create Normally Closed Contact with Electronic components.

    Hi Klaus, Thanks for your reply. Please note that control signal coming from TRIAC, SCR and Microcontroller network. I don't want to use mechanical relay. My requirement is that if control circuitry fails because of any reason then my Fan should be kept ON through "Normally Closed" contact.
  3. H

    To Create Normally Closed Contact with Electronic components.

    Hello Everyone, I need to design a "Normally Closed" (NC) contact with Electronics components with following load requirements, Load Voltage = 230 VAC Load Current = 2 A Max. Load = AC Motor please suggest any low cost solution for the same.
  4. H

    Bidirectional TVS Diode application

    Hello, Is it possible to use Bidirectional Transient Voltage suppressor (TVS) Diode in 230V AC supply Section across primary of any transformer i.e. before rectification??? My requirement is to protect my system from unwanted Spikes & surges coming in from input supply...
  5. H

    To use electronic ballast output to get 230 V AC to run LED Tube Light

    Hi, I am having a LED Tube light which runs on 230 VAC supply. I want to use this light on conventional tube light fitting having an electronic ballast without any modification in wiring at both the ends of tube light. Can any one tell me about how to get 230 VAC from Electronic...
  6. H

    To import hatch patterns from Autocad DXF file to Altium designer 09 PCB file

    Hi, I am using Altium designer Summer 2009 for PCB Designing. I want to import a hatch pattern from a autocad DXF file to AD Summer 09 PCB file. I also want this imported hatch pattern should automatically get its respective net list in PCB file. Can any one help me for...
  7. H

    [SOLVED] To change Footprint of copmonents in Altium Designer Summer 2009

    Hi Kick, Thanks for your advice, it works very well and very much useful for me.
  8. H

    [SOLVED] To change Footprint of copmonents in Altium Designer Summer 2009

    Hi, I am using Altium designer Summer 2009 for PCB Designing. In my schematic I am using 300+ LEds, now I want to simultaneously change footprint of these 300 LEDs in AD Summer 2009. Can any one give me tips to do this ???
  9. H

    [SOLVED] Unwanted Square around pointer in Altium Designer Summer 2009

    How to remove Unwanted Square around pointer while editing PCB document in Altium Designer Summer 2009 as shown in image in following link https://obrazki.elektroda.pl/1874288800_1407499575.png
  10. H

    Finding Short circuit in PCB with Altium Designer Summer 09

    Hi, I am using AD Summer 2009 For PCB Designing. Can any one tell how to locate (Highlight) exact location of unwanted short circuit in PCB after running DRC.
  11. H

    Altium Designer Summer 2009 - Reverse Engineering PCBs

    OK Noted. Thanks for your Valuable guidance - - - Updated - - - I got some notes from altium regarding reverse engineering a PCB. Please check following link for the same http://techdocs.altium.com/display/ADOH/CAM+Editor+Reverse+Engineering+PCBs
  12. H

    Altium Designer Summer 2009 - Reverse Engineering PCBs

    hi, I am using Altium Designer Summer 2009 for PCB Designing. I am having a set of Gerber files and want to create a PCB Document file from this gerber data. Can any one tell me any simple procedure to do this?
  13. H

    TRIAC Based Light Dimmer

    TRIAC is Permanently damaged.
  14. H

    TRIAC Based Light Dimmer

    Hi, Please go through below mentioned link for Circuit https://obrazki.elektroda.pl/7349102000_1399356126.png

Part and Inventory Search

Back
Top