Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi everyone! Hope you are all keeping safe and healthy.
I am trying to detect a terahertz (THz) signal at 350 GHz modulated at 200 kHz with a sine wave. However, no matter what I try I am not able to detect any signal. The synthesizer uses a 9x multiplier and there is no mixer unit at the...
Hello,
I am trying to simulate antenna on CST studio, but instead of using the usual power sources (ports), I would like to use a circuit (Inductor, capacitance, current source). Is it possible for CST studio? Or on ADS? How?
What would be a good software for that?
Best regards,
Hello,
I am trying to simulate antenna on CST studion but instead of using the usual power sources (ports), I would like to use a circuit (Inductor, capacitance, current source). Is it possible on CST studio? Or on ADS?
What would be a good software for that?
Best regards,
Hello,
I am trying to simulate antenna on CST studion but instead of using the usual power sources (ports), I would like to use a circuit (Inductor, capacitance, current source). Is it possible on CST studio? Or on ADS?
What would be a good software for that?
Best regards,
Hello,
I am trying to simulate antenna on CST studion but instead of using the usual power sources (ports), I would like to use a circuit (Inductor, capacitance, current source). Is it possible on CST studio? Or on ADS?
What would be a good software for that?
Best regards,
Hello,
I am trying to simulate antenna on CST studion but instead of using the usual power sources (ports), I would like to use a circuit (Inductor, capacitance, current source). Is it possible on CST studio? Or on ADS?
What would be a good software for that?
Best regards,
I am trying to get the value of the h field with a horn antenna as a reference antenna. I used a 90 degrees waveguide twist with the horn antenna in preset to measure le level of the received signal. But I am getting strange values.
Am I proceeding the right way to measure the h field? If yes...
I am modeling a structure but I get an error like "Body's bounding box exceed valid box. Body size is outside dynamic range of the 3D modeler".
Some literature says that the Boudaris conditions on CST studio have to be set to "Open". I have tried that but it did not work.
Any help?
Thanks :)
Hello!
I am designing a planar antenna rod array. I have tried differents designs with different base length and elements number and get differents results.
And I am trying to understand why the slightest change of the length of the base of a sigle element has on the overall gain of the array...
Hello!
I work on an Antenna design with CST Microwave Studio. The Antenna has 6 ports that have to be combined 2 by 2.
Port 5 and 6 have a phase sift of 180. 1 and 2 quadrature sift. Same for 3 and 4.
I tried to used The block diagram on CST to add the couplers but can't get the s-parameters...
This is the structure made with CST Studio.
The inner ring excites the TE11 mode and the outer ring the TE21 mode; there is also something about a phase shift and all the ports not running at the same time.
Your hel would be really appreciated.
best,
Pawsey stub Balun-Matching probel
Hello
i am designing on CST studio a balun but cant get it to work. Return of loss bad.
Please help
this is the configuration
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
