Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by Embedded Partner

  1. E

    Required Embedded Engineer 1-3 years experience

    Skill Set: Embedded C NXP Cortex M3 Hardware debugging No of Positions - 1 Location: Karnataka, India Note: Contact immediately with in 9th July 2014 Please Contact Immediately, +918867772860 Email - careers@unifiedst.com
  2. E

    how to send MMS from SIM300 GSM Module?

    Which GSM Module supports sending MMS ? using AT commands
  3. E

    how to send MMS from SIM300 GSM Module?

    Hi friends How to send MMS from GSM module with AT Commands? I have SIM300 GSM Module
  4. E

    what is the name of the Tamil Nadu common entrance test for engineering?

    Thanks for both of you, where i will get full details regarding engineering collages of tamil nadu? EX: In Karnataka they are mentioned the full details of collages in CET brochure(Which containing all colleges addess,Ph no,and website)
  5. E

    what is the name of the Tamil Nadu common entrance test for engineering?

    in Karnataka CET is made for common entrance for engineering... then which exam need to choose for entering engineering colleges in TAMIL NADU?
  6. E

    Problem in MSP430 compiler?

    thanl for all there was some problem with the hardware ... its solved... and now i am going for the MSP430F5438IPZ controller, i have one doubt in that that is i am using 16Mhz of 2 crystals but in the TI website they are mentioned that need to use 32KHz .... is their any problem if i use 16Mhz?
  7. E

    Problem in MSP430 compiler?

    i got to know... there is some problem with the compiler.... now the options are available but again there is some problem wiwth JTAJ I dont have the driver for MSP430 parallel to FRC JTAG
  8. E

    Problem in MSP430 compiler?

    yes it was compiler error,,,, thank you one more doubt is their any configuration for selecting Parallel port in IAR IDE? ---------- Post added at 14:14 ---------- Previous post was at 14:13 ---------- because when i use serial port for downloading , i was not selected any port in that IDE...
  9. E

    Nokia e63 as gprs modem

    check these liks it may help you Nokia Pop-port pinout and wiring @ pinouts.ru ---------- Post added at 13:26 ---------- Previous post was at 13:25 ---------- Check it also https://forum.gsmhosting.com/vbb/f139/nokia-system-connector-pinouts-455542/index2.html
  10. E

    SPI programming - rising/falling edge of clock

    for more reference on SPI refer these 2 diagrams thats enough
  11. E

    SPI programming - rising/falling edge of clock

    SPI protocol will be same for all the devices i mean if your slave and master both are having SPI protocol that mean that there is a standard for communicating between those devices(that is SPI protocol)... if your slave DIN:latches data on falling edge and Dout: send's data on rising...
  12. E

    anyone who have project in microcontroller using pic16f877a and assembly

    post your requirements(particular) for your project here we will make you to develop yourself....
  13. E

    Problem in MSP430 compiler?

    what may be the reason behind this error(after clicking on the debug without downloading option)? "illegal opcode found in address 0x0"
  14. E

    sms using microcontroller but without using GSM modem

    there are some sites are available through that sites you can............... not using cell phone use some internet dongles
  15. E

    SPI programming - rising/falling edge of clock

    i MSP430 of SPI module , you must sellect the SPI according to ADS1298..... check the clock/timing diagrams of SPi module you get to know
See more

Part and Inventory Search

Back
Top