Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by dovo

  1. D

    Place a Component to the mouse location?

    Hi all, What is Shortcut key for place a component to a mouse pointer location? Thanks
  2. D

    Altium User please help!!1

    I am using Altium Ver.10.391. I want to change all of my TO-90A Thru hole to SOT89L SMD. I got message : " cannot match pads with new footprint". What can I do to replace them? Thanks DV
  3. D

    Creating Split Planes PADS Help!!

    Hi, thanks for answer but I don't understand by clicking on the other side to end the auto plan separate. I upload the image see Is any one have any idea. HTML: <a href="http://images.elektroda.net/97_1331597072.jpg"><img src="http://images.elektroda.net/97_1331597072_thumb.jpg"...
  4. D

    Creating Split Planes PADS Help!!

    I am using PAD 9.3. and try following the tutor to do a split plan. After selected Board Outline and convert it to plan area. And then use auto Plan separate-Set Grid 25 mils. after draw around the plan area, PADS give me a message: All Corners must be within the plane are polygon.. What can I...
  5. D

    Manual Rout with Orcad layout plus 15.5????

    Hi all, I have a component CS144 with 144 pin, and there are 29 of them in board. How can I just manual rout (Fan out) one chip and copy and paste them over 28 remaining chip? Please help DV
  6. D

    How to convert from PADS to ORCAD LAYOUT?

    Is any one could give me a hint How to convert layout from PADS to ORCAD? Thanks a mile. DV
  7. D

    REQ:Help to find GSI gerber photoplotter control software

    Re: REQ:Help to find GSI gerber photoplotter control softwar Give me where I can send it to you. DV
  8. D

    REQ:Help to find GSI gerber photoplotter control software

    Re: REQ:Help to find GSI gerber photoplotter control softwar I have GPC/GPQ latest Version. It use for Sun Box. After installation you have to have the password to run. This Password is tied with System ID number. I am looking for somthing to generate the password. DV
  9. D

    REQ:Help to find GSI gerber photoplotter control software

    Re: REQ:Help to find GSI gerber photoplotter control softwar Hi do you know that new version of software need new password?. Could you have any thing to generate password. Let me know. I will let you a Copy of S/W. Dovo
  10. D

    How to convert Tango file

    how to open tango for dos files Thank you for all of support. Is Protel V2.8 allso called Protel 99? Thanks
  11. D

    How to convert Tango file

    convert tango pcb sch I have some file under Tango Schematic and layout. How to convert them to one of newer software (Protel, Cadence....)? Thanks Dovo
  12. D

    Parallel Port Simulation ..

    parallel dongle simulieren Thanks all, I solved this problem ok.
  13. D

    Parallel Port Simulation ..

    paralel port simulator You mean PCMCI SLOT? yes I have one.
  14. D

    Parallel Port Simulation ..

    parallel port simulator Hi all, I just buy a Laptop (Toshiba Satelite p35) that does not have any Parallel Port (Just usb). I need to install Genesis that need to have dongle driver install. This software required Parallel port . What do I need to do?. Could we install any Parallel port...
  15. D

    how to make silicone rubber heater

    Is any one in Heater profession plese give me some information about how to make silicone rubber heater. Thank you DV

Part and Inventory Search

Top