Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I have copied the apropriate web address, it's the same as the first google hit for search word "kicad". I'm using Firefox and everything seems OK for me. Try to acces it on the alternative page hosted on **broken link removed**
The transmited data is scrambled before final modulation and transmition. Scramblers are simple circuits realised as a chain of D flip-flop cells and combined with usually 2 XOR gates.
Scrambler provides that the data is not very uniform for example "11110000". Scrambler would cause extra...
It strongly depends upon coeficients A,B,w1, w2.
But in most cases signal would not be periodical but pseudoperiodical if not even nonperidical.
f(t)=A.sin(w1.t)+B.cos(w2.t)
The definition for peridical signals says:
f(t)=f(t+T), where t is time and T period.
so you should solve the equation...
block diagram of pic18f4550
WinPIC800 has a "Verify All" button that does just what you did manually. When pressed it compares the original file with what is writen in PIC. But if you have manually verifeid the content then it's OK.
PIC fuses are setup bits to tell the microprocessor the...
how to program pic 18f4550
No the programming via JDM cannot be the cause of the error. There seems to be some kind of communication error between bootloader and windows. I suppose that when you have programmed the 18f4550 via JDM the verify function passed and you are absolutly sure that...
pic18f2550 icsp programmer
Have you tried to move this driver to another location on PC? If not try:
1. go to C:\WINDOWS\system32\drivers\ and move the file libusb0.sys somewhere else on the computer
2. now windows won't see the driver and maybe it will accept yours
pic18f4550 program how to
So you have followed the folowing instructions form CUI site:
and as I understand windows don't want to pick up the driver you wish. Have you tried to remove the current driver from the Device Manager? If that does not work try to move the currently used driver to...
What about the capacitors as close to ne555 power supply pins as possible? Do you have them? Maybe they can provide a solution.
Have you observed the VDD with oscilloscope? What are the time periods of voltage drops due to the motors?
usb programmer for pic18f2550
The JDM programmer that you have attached is my first PIC programmer. On my computer it has worked flawlessly, although there are some probems posible with the modern PC's since RS232 in original demamnds 13V of voltage and most of the modern RS232 devices will...
pic18f4550 programmer schematic
Yes you still need to program the 18F4550 that goes into the ICD2 programer before you assemble the ICD2. Empty chip in ICD2 won't do the work it should have.
Once you have the ICD2 assembled with preprogramed 18F4550 and 16F877 it's working and you can program...
programing pic18f4550
On the linked site there are at least 3 versions of USB based ICD2 programmer/debuger. There are schematics, PCB's anf needed firmware for 16F877A and 18F4550, all you need.
I'm using a B version od USB based ICD2 clone from user PICs with no problems.
Read throu the...
program pic18f4550
NO, no, no! You have missunderstand the serial in ICSP. It does not demand an serial PC port. If you look at the link in one of my previous posts to ICD2, you will see that it is USB based!
The word serial in ICSP implies only to protocol for programing, that is the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
