Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by DigitalWork

  1. D

    What software to use for Simulation

    Hi Mentor :-) , I am a newbie in electronics. I have studied electronics in academics. All it was theory. But if you go for job the practical electronics is used. And we have to learn how to convert theory which u learnt in academics to practical version. My point is I want a simulation...
  2. D

    Sensors used for Water Level Controller Project

    Hi Mentor, I want to make a project Water Level Controller and want to know about different type of sensors used for UnderGRound Tank and OverHead Tank. Are there sensors which show the Upper Level and Lower Level of Water in OverHead Tank.What are those sensors? Plz Help Thanks in advance.
  3. D

    I want to learn how to Design a Circuit

    Hi Mentor, Thank you for taking me one step further.:-)
  4. D

    How to Define value of Resistor used for LEDs

    Thank you Mentor it helped a lot. One line I did not understand is :-A LED is a constant voltage device, that means it takes almost no current until you apply "Vf", it's forward conduction voltage but from there on it tries to hold the voltage constant by drawing more and more current. Does...
  5. D

    How to read a datasheet

    Hi Mentor, I know how to read Mechanical specs but do not know how to read or what to read in Electrical Scope. For general ICs as Opam,DAC,Microcontroller,Wifi IC, LDO etc IC what we require from datasheet Thanks in Advance
  6. D

    How to Define value of Resistor used for LEDs

    Hi Mentor, Thank you :-) for clearing my doubts and giving basic knowledge about choosing resistors and LED function.Now I can imagine a clear picture.Thanks As you have mentioned that LEDs cannot be made same like bulbs where in bulbs we don't require constant forward voltage why LEDs can't be...
  7. D

    How to read a datasheet

    Hi Mentor, I am a new bee to electronics. I want to know how to read a datasheet of any components. Thanks in Advance Sincerely DigitalWork
  8. D

    Whats theDifference between Earth and Ground and Digital Ground and Audio Ground

    Hi Mentor, How are You? I am a new Bee. If I see a circuit it is filled with various Ground like Earth and Ground and Digital Ground and Audio Ground. What is the difference in all those Grounds. Does all give 0V or there is somthing else which I don't know. Thanks in Advance Sincerely DigitalWork
  9. D

    How to Know what current and Impedance and voltage flowing in some IC.

    Hi Mentor :-), I am a new Bee to electronics. If I have a circuit consisting of various Ics and Power supply circuit. If I do some modification to the circuit i.e suppose I want to add a LED to the Line of one IC may it be Micro controller, or want to add Pull up resistor to the pin which...
  10. D

    I want to learn how to Design a Circuit

    Hi Mentor, How are you? I am a beginner in electronics. I have studied Electronics in College but that was all theoretical. If I want to design a circuit how to use that theoretical knowledge to convert to practical knowledge. Do we require imagination power of how current flows how voltage...
  11. D

    What are Pull Up and Pull Down Resistor with Applications.

    Hi Mentor , I want to know about Pull Up and Pull Down Resistor with Applications. Thanks in Advance DigitalWork
  12. D

    How to Define value of Resistor used for LEDs

    Hi Mentor, I am a beginner in electronics. I want to know that what value of resistor to be used for LEDs. Also when LEDs are in parallel and when they are connected in series. What all happen internally means how much current flows . How much voltage gets drops. and does the current flowing...
  13. D

    What is PCB Reverse Engineering

    Hi Mentor, :-) I am a PCB layout designer and I want to know about PCB Reverse Engineering . The tools and techniques involved. The whole Process.What Should I require(tools) to do reverse Engg. And also about how a black blob PCB reverse engineered. and how to reverse engineer a more than 2...
  14. D

    I need help in designing a circuit of which use motion sensor

    Hi , Thanks for the quick response. The sensor is not much important it can be light or motion sensor. The circuit is main important. May be it motion or light sensor it(the circuit) should fulfill the purpose.:smile:
  15. D

    I need help in designing a circuit of which use motion sensor

    Hello! I need a circuit in which motion sensor is used to turn on the lights of the room and also turn off when not required.

Part and Inventory Search

Top