Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I've seen some design in this forum for a dc-dc boost converter for Nixie tubes running at 180V.
Though all designs I've seen are running from 9V DC supply and more...
This week I came across this item on ebay, and it looks like it is using a LT DCDC converter chip and a MOSFET packaged in...
Been a long, long time I visited this forum, but finally I'm back into electronics ;-)
Did any1 use any chipset for doing a FXS adapter to hook up analog phones onto VoIP?
I've seen Microsemi and SiliconLabs doing some chips, not sure if any more do some chips.
Good evenin'...
There are some rather old posts here from people who started or wanted to start developing a USB device based on TI TUSB3210/TUSB3410...
I just grabbed out my old board based on TUSB3210 I made some years ago to use as a simple USB interface for testing SPI/I2C devices under...
Good day (o;
Remember the good old days when Dynaudio loudspeakers were available as chassis to built selfmade TML loudspeakers of excellent quality...but since they don't sell it anymore...
Which chassis do other people recommend/use for building their own HiFi speakers?
thanx in advance...
If you would have checked https://www.altera.com/literature/hb/nios2/n2cpu_nii51015.pdf you would know NIOS2 isn't supported on APEX device....
For OSPF or any router related stuff have a read at:
https://www.embeddedrelated.com/usenet/embedded/show/91649-1.php
If you figure out to do a OSPF...
cisco vs juniper
One big advantage is with JunOS that you can run it as so called "Olive" image on a regular PC or under VMWare for simulation as the underlaying OS is just FreeBSD...
**broken link removed**
Also for example the new MX series draw much less power than a comparable 7606S with...
Is someone already using the new ispLever 7.1 for Linux with included Synplify Pro?
I'm only able to do EDIF projects for only 1 specific FPGA...
Running Synplify Pro standalone is working fine though...
download drivers for usb blaster
I'm also not familiar yet with the whole source code yet (o;
Just used the Lattice USB cable for verifying the source code and how to adapt it for hardware changes...
At least I can progam with it my Cyclone devices without problems now as I don't have any PC...
altera usb-blaster urjtag
Thought I share my experience with building an USB Blaster based on FX2LP from Cypress...
As I already got an USB Cable from Lattice which uses the same chip, although 100 pins, I removed the SDA pin from it so I can download own firmware for testing...
First...
Evnin' (o;
Has anyone used PowerLine modems in a design?
Which manufacturers supplies approved embedded modules for a drop-in design?
Any pointers welcome....can't afford building own powerline module due to expensive regulation costs (o;
Hello (o;
Has anyone worked with off-the-shelf powerline modems to be used in ucontroller applications?
Target is to communicate with a low baudrate over 230V main line, for example to send messages or synchronize clocks...and they should be off course small and cheap (o;
thx in advance
Re: Unix/Linux
Please don't write rubbish....
Neither UNIX/Linux have something to do with graphics....it's the X window system available for all major flavours which does it...and there is no "grahical mode" at all (o;
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.