Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
thanks you
i decide to use one of pam8xxx
and forget the circuit from post#1
the main problem is the power source
it toke me in new way by use
mini Rechargeable battery »» Switching Power unit
and stabilize the volt
i read PAM8403 data sheet
Absolute Maximum Ratings : Supply Voltage =6v
how about make voltage divider and stay at 5v?
file Attached
- - - Updated - - -
right to ground ~= 0.7v
left to ground ~= 0.7v
thanks mr BradtheRad
it will be my next option
if Switching Power supply not work
- - - Updated - - -
thanks every one
- - - Updated - - -
thanks every one
thanks mr Audioguru
i can do Switching Power supply unit that use XL6009
and search for another op amp
but do Switching noise here ignorable ?
also dose coin cell suit for Switching ?
so if Switching is not recommended i will reduce gain from 3 to 2
thanks mr d123
seriously you helped me
i want very few component and lite circuit
so i plan to use coin cell
first
a rail-to-rail
if not
i have to lower the output
- - - Updated - - -
from post #5
thanks mr Klaus
ok i will do google search for dedicated earphone ic and after read it data...
sorry you say: Maybe use class D amplifier with low pass filter.
my project have 2 input so i guess you mean classic old class D amplifier one input one output
not ic based on class D amplifier technology
someone set behind keyboard wait for reply from he's admire teacher
reply come that...
thanks mr Klaus
ok i will do google search for dedicated earphone ic and after read it data sheet i will post my effort
about class D amplifier is it will be 2 unit ?
one for right and second for left ?
thanks mr Brian
ok i will use capacitors and load resistor
i want to use LM158 but from it data sheet
Input Voltage ( -0.3V to +32V )
but my Input Voltage go to (-0.7)
sorry im confuse about -0.3 and -0.7
is -0.3v mean the lowest input voltage ?
hi every one
i want to amplifi audio signal from phone
i have ear headphone with low sound
to do that i want to use smd dual op amp
1/2 for right the rest for left
vin =0.7v , power in= 1mw
gain=3
power source : 2 coin cell 3v
speaker = 600 ohm (from some set)
could it work without lead from op...
yes it's alot of power
but i have to do it
no i can't use household electricity for the application
you know mr audioguru i assume you think all about dissipation as heat
it because my plan is doubtful
as it clear i can use either
modified sin model or pure sin wave model
thanks you for being...
ok mr Audioguru
i need 220v ac . 50hz
power 3000 w
so
i will start to make the circuit
with pwm model
using pic microcontroller
and post the circuit here
thanks for help
thank mr fvm for reply
if i design circuit like audio amplifier that amplifer 3 or 4 volts sine , 50 hz
and feed them to transformers to be 220 ac 50 hz
can it be
first im here because before 2 week ago i see one of your
reply for someone
it help me
and now i see all the magic here in this forum as good people
now if sg3524 not work here
as i understand from your reply
sorry may you suggest another way or another ic
also mr betwixt Excuse me im...
All what i think about
is that generate 220 ac from 12 ac without ripple
for that i think i can use sin wave source
thank mr Audioguru
now i understand thate connect 2 transistor in series with same input signal will make them short circuit
thanks
also Excuse my bad english
thanks mr audioguru
Excuse me im bad at english
im think to use that sine wave signal
also i know that the circuit most contain push pull stage
now if i replace ic sg3524 with
two ic8038
can it be or the same error
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.