Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by Bosechandran

  1. B

    python issue

    Hi, i have set of program which will run in python 2.7 but it shows below error how to fix the bug. Traceback (most recent call last): File "C:\Program Files (x86)\Texas Instruments\AFE5832LPTX EVM\Scripts\Swaroop_Automation.py", line 20, in <module> HSDC_Pro = cdll.LoadLibrary(dll_path2) File...
  2. B

    verilog code needed for my sequence

    ok thanks, I will do it. thanks for suggestion
  3. B

    verilog code needed for my sequence

    hi i need verilog code for my sequence 01 2 3.....................63 1000000000............0 0100000000............0 0010000000............0 0001000000............0 0000100000............0 0000010000............0 0000001000............0 0000000100............0 i need shift register code. This...
  4. B

    sequence issue in transducer i/o

    Hi, I have 8 high voltage pulse and I want to connect with 64 element transducer. sending the 1-8 element, to receive signal in all the other elements sending the 2-9 element, to receive signal in all the other elements 3-10 subsequently suggest me which high/low voltage...
  5. B

    [No title]

    Re: verilog delay problem no need to do my job. its a 0.01% in my work. just asked a friendly manner. u r not eligible to criticize me. sorry others
  6. B

    Unable to get output from pulsed laser diode module - 905nm

    Hi , I am working with LS9-40/220-30/100-S10-11 pulsed laser diode module purchased from LaserComponents, Germany. I have made all the required connections but I am not able to sense any output light even when IR card is used. Following is the pin conf: pin 1 : +12V DC pin 2 : 0 to +5V, to vary...
  7. B

    8 channel high voltage ultrasound pulser

    i have max2082cdx+ i want make a board around it if possible help me
  8. B

    8 channel high voltage ultrasound pulser

    im going to use 70v dc supply
  9. B

    8 channel high voltage ultrasound pulser

    hi i want to make 8 channel ultrasound board i have max2082cdx+ ic only. i want to make a board around it i designed 8 parallel input signal from fpga need to fed into the octal high voltage transceiver ic. but i have that ic only need i/o distribution casing or board and other accessories...
  10. B

    cypress usb not detected

    Dear Sir, i have designed verilog code and i have spartan 3e kit which is used wave share board so i easily connected cypress usb board (cy7c68013a). i install cypress driver and i open it. but the hardware not detect. i want program to the board. help me thank you
  11. B

    [No title]

    verilog delay problem Dear sir, how to increase or decrease delay between two pulses on a same signal. i want after every two pulse need some delay. expecting verilog code. i tried verilog code both u down clock pulse width vary or getting delayed out. i dont want that thank you
  12. B

    supply for fpga board

    thank you sir
  13. B

    supply for fpga board

    dear sir shall i use desktop pc usb output power for fpga 3s250e power supply. usb output is 5v and spartan kit power requirement is 5v. data transfer is different. im asking about power to the board. thank you
  14. B

    need verilog code for biphasic waveform generation

    Re: To generate biphasic waveform thank you for ur suggestion i quit searching i try proper coding myself and add some analog circuitary
  15. B

    need verilog code for biphasic waveform generation

    To generate biphasic waveform i want to generate biphasic waveform with pulse 12.5 ns in verilog/vhdl my system clock 50MHz.
See more

Part and Inventory Search

Back
Top