Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hello,everybody;
I got a PROTEUS component model of microphone
at this forum that is;ISO-8859-1__MIC.rar(I attached it here) ,but I
don't know how to add it to my PROTEUS and use it.
Would you please tell me how and in which folder should I place
the; ISO-8859-1__MIC.rar / MIC.DSN ,in my...
Hello,
With thanks,how and in which folder should I place
the; ISO-8859-1__MIC.rar / MIC.DSN ,so that my
PROTEUS has microphone component to use it for
projects?
Thanks,
Hello everybody,
I designed a 6-channel remote control to control 6 devices
and used a PT2272-M6,a CD4050 ,a CD4532 and a L293D to control
2 dc motors; move right,left, forward and revers : thery are 4 channels.
As you see in my.png attachment, I connected the Q0,Q1 and Q2 pins
of CD4532 into...
Hello,everybody.Would you please tell me if my following understanding is correct?
**I think the maximum speed resultant that achieved in a Dc motor when using PWM method
is equal to when directly applying a battery[dc power] into that DC motor and if I still want
to increase DC motor's speed...
Problems with switch instruction in mikroC PRO for PIC?!
Hello,everybody.I wrote a program consist of few functions.And in each functions I used switch instructions and at
each case of the switch instruction I called one function.But it gives me some errors that you can see at the following...
Hello,everybody.I want to measure Ac currents and voltages with the following specifications;
My circuit & program code specifications;
Applied AC voltage 100Vpeak via a 1/20 resistor network attenuator to AN0/pin2 of PIC18F452/XTAL;20MHZ.
I wrote a program to show 25000Vrms/35355Vpeak,so we...
Hello everybody.I want to write a program using PIC18F452&XTAL=20MHZ in C or mikroC to do the followings;
1.Simultaneously turn a timer on[timer0 or...] to count for 1 sec. and
also count the number of High[transition from H to L] state of the
input signal.
2.Turn a timer on[timer0 or...]...
Hello,everybody.I write a program to measure the input signal frequency by using an TMR0 interrupt and A function to display it on a LCD.But my TMR0 interrupt function does not send counter varaiable[cntr] to my
displaying funtion or maybe not worked well,because I have only ; FRQ.= 00000 HZ on...
Hello,everybody.I want to read an int and a char from row=3 and column=1 on the PG24064F GLCD[T6963C DRIVER]; [I have these on my GLCD 1. (x=3,y=1) ; T= 25000 and want to read only 25000 from GLCD and save it in a array x[i] 2. I have a char at (x=7,y=10); Apply and want to read it and save it...
Hello,everybody.I wrote a program using; PG24064F GLCD [ T6963C driver/display 240x64 pixels ];
simply showing;[Hi,] at the row1 and indicating the dc voltage measured by the ADC channel 0 of PIC18F452
at row2 as;[Vdc=...v].I used the mikroC PRO V2.50 library routine but I got nothing on the...
Re:But why my program display wrong numbers on the LCD!!!???
Hi,Mr.Tahmid.Thanks a lot for your helpful reply.But why my program display wrong on the LCD.At low range for example;1.5v and 2v display 1v or 0.05v up t0 1.4v display 1 or 6v display 5v,..at only a few range display correctly!![I...
Re: problem in mikroC for PIC V6.2 & V8.2 compiler//RE[2]
Hello.Thanks,but I wonder it begins to give error just after 9k;before it[9k]
it works correctly.
Thanks,
Hello,everybody.I wrote a program with mikroC/PRO2009/V2.50 and used;
t0 = ADC_Read(0); instruction.Now I want to now what is the type of the contents of t0 = ADC_Read(0);that is BCD or BINARY? It is necessary to convert it to DECIMAL? and how?
Thanks,
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
