Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by benbiles

  1. B

    capacitor polarity question

    sorry , I just realised I never replied to this !!!! Thank you Klaussss and thunderdantheman for your help on this. It's finally all working. I now have the 8 channel ADC and DAC VQ buffered to the preamps / line drivers and HP driver cards. I have ADC and DAC VQ's biasing OPA1367...
  2. B

    capacitor polarity question

    was meaning do you think the differential op amp would work well for the main audio buffer/filter to the ADC? how about TLV6001 to buffer VQ? only have 4 channel version.. maybe I can dead bug one onto the ADC board and just see if its noisey or not! It would be nice if I could voltage follow...
  3. B

    capacitor polarity question

    Yes, VQ decoupling still there. I meant by 'bypassing' that I just soldered the DC decoupling cap legs together so there 6.3v 10uF decoupling caps are out of circuit. It's both a combination of lack of detail in the datasheet and me still not that experienced at building analogue circuits. I...
  4. B

    capacitor polarity question

    thanks thunderdantheman for your detailed explanation :) yes , I had presumed the decoupling caps for VQ are required. I had not understood CS5368 analogue inputs need to be DC biased in order to function correctly at full voltage swing. I connected PGA2500 VCOM to VQ and bypassed the...
  5. B

    capacitor polarity question

    Hi Klaus, PGA2500 -> 10uF cas --> CS5368 I have PGA2500 VCOM tied to GND I was following pga2500 datasheet Figure 8. PGA2500 Analog Output to ADC Analog Input Interface, AC-Coupled on CS5368 I tried leaving VQ with just caps to GND as in datasheet example. I also tried VQ with VA/2 =...
  6. B

    capacitor polarity question

    Caps to decouple DC mismatch between preamp and adc? 10uF is the right cutoff, but I may change that. For now I want to be sure there is no DC mismatch or problem. I think the correct name is DC decoupling? The 8 channel ADC gets very warm, about 55C and I'm thinking it might be working to...
  7. B

    capacitor polarity question

    I am using some electrolytic 10uF capacitors to hopefully filter DC bias that exists between an ADC and a digitally controlled preamp chip. PREAMP -> ADC INPUT The preamp, TI pga2500 sergests using capacitors to decouple the preamp output from the ADC. The output of the preamp and input of...
  8. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    sorry c_mitra. yes thanks , I tried to edit message above and it got messed up ! ebike load = 20A @ 37V 740W -> 10 series battery packs x 3.7V 20A 74W going with betwixt I^2 * R 20A ^ 2 * 0.185ohm = 75 75 A ? a fuse rating should be 4 x times the maximum load ? does that sound...
  9. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    I have 8x cells in parralel to make 10 x 3.7v battery packs. Let's just see them as battery's that need some short circuit protection Those battery packs will be in series and monitored with a BMS to make 36v nominal. If I draw 100 amps at 36v each battery pack contributes 10 amps at 3. 6v or...
  10. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    That's really good advise ! thank you ! I have a load instrument but I don't think it goes up to enough amps at 3.7v to blow the fuse. I have to say I'm a bit confused with how I should calculate this. If I have 36v made up from 10 x 3.7v battery packs. If I draw 20amps at 36v from the large...
  11. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    Yes I know. I assume there aren't many 3.7v 150A or 200A rated fuses out there?So I chose to discribe the fuse in W rating :) Can I used a 12v 50A fuse as a 3.7v 187.5A fuse? Both 600W? Or do I have my ohms law wrong?
  12. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    1610345797 Great solution, thanks. I should be able to find a blade socket to. I'll work out with ohms law what amps it is at 3.7v 12v 50A is probebly enough but cheap as chips to chnage
  13. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    A home 110v breaker is quite large. I was Looking for a self reseting fuse. I want to keep the contacts as close to the metal strips that parralel the 8 x 18650 battery's as close to the contacts that will connect to the backplane as near as possibe. So large breaker there would be impossible. I...
  14. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    yes, that makes sense. 10 x 36v battery packs monitored with a BMS is less parallel than 8x3.7v cell in parallel in every battery pack ? So maybe since I need 36v min. I should go for slightly less mA hour 18650 cells and put 10 in series for each module. that way I can get 36v 100Wh packs and...
  15. B

    [SOLVED] Lithium battery 8P1S 3.7v nominal 4.2v Charge high current protection

    I am making multiple 8 x parallel(lithium iron 18650 3.7v 3400mA) battery packs that should be under 100Wh capacity. The individual cells are not protected for over current. Each x8 cell pack will need some kind of short circuit protection >100A , 135A ( 500w ) The x8 cell pack has no...

Part and Inventory Search

Back
Top