Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by BD

  1. B

    Displaying Images on a Mini TV/Nonitor

    What does a Video signal look like on a Scope? Should all Video signals look the same? How do i correct a video signal so it appears ok on my Screen. It appears to have the correct DC level,but the signal Boms out every couple of seconds, Is there any way i can clean up a Vidoe signal.
  2. B

    Where to start designing matching networks?

    Re: Matching Networks. Yes, It is matching a 75ohm load to a 50ohm source.
  3. B

    Where to start designing matching networks?

    Matching Networks. Hi, does anyone out there know anything about Matching Networks. I want to Design matching networks to operate at a frequency of 750MHz, and a bandwidth of 10MHz to match a load of 75W to a source of 50W. where should i start.
  4. B

    Microchips KEELOQ Devices

    Hi, Has any one got any information on using Microchip's KEELOQ Devices, espically the HCS410 Evaluation Kit Base Station.
  5. B

    How to read the Hex File of a PIC Micro

    read hex file from micro Hi, I wish to read the Hex file from a no. of PIC 16C63 devices. I have a PICSTART Plus programmer. How should i go about doing it. Will i be able to use the PICSTART Plus with MPLAB v6.51 Thanks
  6. B

    Programming KEELOQ Devices, pin out diagram required

    keeloq diagram Hi, I am lookin for the pin out diagram from the HCS410 Evaluation Kit Base Station to connect to a KEELOQ encoder to program it. I am goin to use a PIC micro on the Evaluation board to program the Encoder.
  7. B

    Using Microchips HCS410 Evaluation Kit

    Hi, I wish to find the pin out required to program a HCS412 from the HCS410 Evaluation Board.
  8. B

    how to reduce heat in circuit

    would the switchig frequency have to be totally uniform. could a slight time delay in switchig cause the rapid increase in Temperature
  9. B

    how to reduce heat in circuit

    how can i reduce the amount of heat my transformer is dissipating. two transistors control the transformer,one on one off i.e. switching current, but the transformer heats too much. any ideas.
  10. B

    Help me locate a company that puts SK symbol on component

    Re: Locating a Company. Thanks Guys, Just lookin now for two more components, (1)An 8 pin IC,surface mount component.with markings 10358 4R95 (2)and another surface mount component an 32 pin uC there is a symbol in the corner of the device. does any one know where this IC could be got...
  11. B

    Manufactureur of Electronic Components

    Thanks Guys, Just lookin now for two more components, (1)An 8 pin IC,surface mount component.with markings 10358 4R95 (2)and another surface mount component an 32 pin uC there is a symbol in the corner of the...
  12. B

    Help me locate a company that puts SK symbol on component

    Re: Locating a Company. Hi, I wish to find the manufacteurer of a number of components,but i only have the markings on the devices to locate the manufacteurer.I need to source the data sheets for the particular devices, Could anyone please help me the items are as follows. (1)Transformer...
  13. B

    Manufactureur of Electronic Components

    Hi, I wish to find the manufacteurer of a number of components,but i only have the markings on the devices to locate the manufacteurer.I need to source the data sheets for the particular devices, Could anyone please help me the items are as follows. (1)Transformer MDS-NS-10...
  14. B

    Help me locate a company that puts SK symbol on component

    Re: Locating a Company. Hi, The part is a FET of some kind.A 3 legged through hole component with a G,D,S. the numbers on the component are K2098.
  15. B

    Help me locate a company that puts SK symbol on component

    locating a company Thanks for the information, I found the components data sheet. I am now looking for another Company. the component has a symbol which looks like an FE, Would any one have any knoledge of this company.
See more

Part and Inventory Search

Back
Top