Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
MICROCAP User Source .USR not working
I get that error when I try to use v(out2). No problem with v(out1)
The problem is neither Data Point Count nor number format.
Same trouble with Microcap 12.2.0.0 now for free and with an older version.
I have no clue.
files.7z incudes...
Yes, from two stereo analog (not Class D) amplifiers I want to sum both output below 100 Hz.
Using passive LC network (i.e. not summing at low level and then amplify sum signal)
I think the problem is not the new loudspeaker lowering the impedance, because when amplifier sees the woofer it...
I want to add a woofer to a stereo amplifier. I want to sum both channels, L&R, at low frecuencies.
Medium and high frecuency speakers are the original ones drived by the highpass LC filter.
Low frecuency (woofer) is tricky. I just can't connect both low pass output together to the woofer...
Microcap simulator from Spectrum Software. Those guys are developing their simulator since 80s (at the beginning it was DOS!). They have assembled the features we need in a very intuitive way. Models and algorithms for solutions are the very best.
Do give it a try: MicroCap download
I have hundred (even thousands) of PDFs; I need to know which have OCR already made in order to be sure any index I'd make will include all PDFs.
¿How do you do a list of PDFs lacking OCR in order to add them OCR later?
**broken link removed**
**broken link removed**
Feedback loop switch on/off W1 to keep VLOAD = Vref±δV. It switchs off W1 and inject current when VBatt goes down. When Battery is charged W1 is switched on and no current flows into VLOAD
X1 adds hysteresis
X3 and V1 models real world battery...
I don't have the 35MB file any more.
Most of the 35 MB is NIST 1337 document, download it from **broken link removed**
You can get all the other files from de web. I can´t upload them here because each of these files is available in other websites (I don't believe a personal compilation makes...
TO-224 package
I need footprint for MMT3799 transistor mmt3799 smd.pdf - 0.13MB
mmt3799.jpg - 0.03MB
According to http://www.americanmicrosemi.com/information/spec/?ss_pn=MMT3799 it's a TO-224 but I can´t find this package.
Doy you know a website where to find it?
Re: Locked FAN detection
I mean
1) voltage levels
2) pinout (if it's standarized. I'm no sure central cable is sensor output, my fan has a central black wire and yellor and red on the sides... I'd bet red=+12VDC, and black=0VDC)
and I'd add logic (open colector?, normal = HI?)
partocc
I get this error when trying to import properties
I'm using Orcad Capture 9.2
The beggining of my .EXP file is
Any CLUE to solve this problem???
Regarding to error message "ERROR [IMP0021] (Line 177) Occurrence not found" Which is the line 1 in the .EXP file???, The one with the...
it's a matter of convenience. It's better to tie all your analog returns by one side (analog ground), all your digital retuns by another side (digital ground). Eventually does exist a third common conection, namely chassis o "earth" which is connected to real ground (the planet). It's for safety...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.