Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by ArakelTheDragon

  1. ArakelTheDragon

    Use "Vector VN1610" and a serial terminal instead of "Vector CANoe"

    Use "Vector VN1610" and a serial terminal instead of "Vector CANoe" Hi guys, I hope this is the correct place for my topic, if not please move it. I am trying to get a serial terminal to work with "Vector VN1610" because I prefer to use it instead of "Vector CANoe", on "CANoe" everything...
  2. ArakelTheDragon

    problem with pcb etching

    I got rediredted to some pic site "tumblr" or something and I have to register, cause myself problems and I don't think this is your server? There were good pics of kittens on it.
  3. ArakelTheDragon

    problem with pcb etching

    I tried that, but it did not work.
  4. ArakelTheDragon

    problem with pcb etching

    Result: the problem really was the etchant. It turns out that only the upper part of the copper was removed, when I scratched the PCB, I saw the rest of the copper layer. Until it turns full plastic and you can look through it, when you point it towards the sun, its not ready...
  5. ArakelTheDragon

    problem with pcb etching

    I will increase the etch time 24 times and check the results.
  6. ArakelTheDragon

    problem with pcb etching

    I am using printer toner and a marker for the tracks. I don't think the "sun bath" will remove these residues?
  7. ArakelTheDragon

    problem with pcb etching

    I understand. 0. Here is a link to the process. 1. Here is a link to the dropbox picture.
  8. ArakelTheDragon

    problem with pcb etching

    It was hard to decide which information is needed, thats why I did not post anything. I can give you a picture if that will help, but I expected the chemicals to have removed all residues. The whole PCB is conductive as if I have not etched it at all.
  9. ArakelTheDragon

    problem with pcb etching

    HI guys, I etched A pcb, but after the copper fell, when I use the multimeter, the etched part is still conductive. Can anyone help me solve this please?
  10. ArakelTheDragon

    Good cheap DDR4 RAM memory site

    Hi guys, I found this site which offers a lot of things from "AliExpress", but they filter the sellers for us and only offer us the high quality. If you need something that they don't have, send them an email and they will find the best seller on "AliExpress" for it and give you a link back...
  11. ArakelTheDragon

    Low price but good quality PCB manufacturer in China

    If it does not have to be in China, you can check these from the EU.
  12. ArakelTheDragon

    Canoe: Driver - Reception overrun : Messages are lost

    Page 9-10.
  13. ArakelTheDragon

    SPI protocol with SD card

    Can you post a circuit? If your module has SPI, you connect it to the MCU and then from the MCU to an mp3 player chip, you might be able to skip the MCU.
  14. ArakelTheDragon

    Intel® Core™ i3-350M Processor

    I think you want details about proprietary technology. The site I gave you should have a datasheet. Otherwise you need to contact intel about this information.
  15. ArakelTheDragon

    Intel® Core™ i3-350M Processor

    Hi! You have to search on specificarion with the second search box. i-350m
See more

Part and Inventory Search

Back
Top