Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by anum_pirkani

  1. A

    Quadrature Phase detection module

    Hello everyone. I have been given a task to design 'quadrature phase detection module' for an RF Receiver but i am unable to understand its need and function. The one i have been asked to design gets two IF signals at its input (sum and difference IF signals). After passing through amplifier...
  2. A

    Passive Phase lock loop

    Hi.. I am looking for a PASSIVE PLL component that I can use after VCO followed by 2 way power divider in my design. I have searched for PLL but i have found active ones...!!! Frequency is approximately 900MHz VCO------PASSIVE PLL-----2-WAY POWER DIVIDER Regards
  3. A

    [Moved] Can i use AD8062 instead AD8611

    Hi. I wanted to ask if a could use AD8062(rail to rail amplifier) instead of AD8611(comparator). I have to invert the input signal.
  4. A

    -5V to the input of NOT gate IC

    I actually have -5V and 5V at the input and at the output, i need 5V and -5V respectively. But i don't know how to give negative voltage to the gate. I am also thinking of using an OP-AMP for the purpose.
  5. A

    -5V to the input of NOT gate IC

    Respected Members, I need 5V output from a NOT gate IC (so. -5V should be the input). How should i give this -5V to the input of NOT gate. Regards
  6. A

    Import ADS file to PCAD

    Respected members, I wanted to know the procedure of importing ADS file to PCAD. Regards
  7. A

    Length of each path of T junction splitter

    Hey Is there any case in which the main arm of Tee junction has same impedence as that of the splitted arms i.e 25 ohms I am trying to design a Tee splitter in ADS for which the information i am given is the frequency and the impedence of main arm and each splitted arm which is 25ohm each...
  8. A

    2 way TEE power divider ADS design

    Hey, I wanted to design a 2 way tee power divider in frequency range of 1.1-1.7GHz in ADS. Kindly tell me the length of each path. Regards
  9. A

    GSM front end ADS design

    Hey I was looking for a simple gsm front end design which i can make and simulate on ADS. Thanks a lot. Regards
  10. A

    electronic filter company with logo M

    hey... Can anyone please tell me which company has the logo M with a circle around it. i am searching for a band pass filter of that company but i am unable to identify the company's name from its logo. I have attached the required image file. I will be thankful to you. Regards
  11. A

    Pie attenuators and receiver circuit.

    I wanted to know the function of pie attenuators when they are in the receiver portion of the circuit. thanks a lot
  12. A

    identification of fuse from fuse number

    I have a fuse with P 100 and P 075 written on it. Can anyone kindly tell me its rating and where can i buy it. Thanks a lot.
  13. A

    [SOLVED] Switching ic required isntead of transistors

    greattt, i got the desired results...!!! i interchanged q2 and q3 previously by mistake. thanks a loads... Regards
  14. A

    [SOLVED] Switching ic required isntead of transistors

    thnkx a lot for the design, it is perfectly switching. i needed a switching topology in which, when one of the switch control signal is high, 1st voltmeter should read around 5v and other around 50v and when 2nd switch control signal is high, 1st voltmeter would give 50v and 2nd 5v. these...

Part and Inventory Search

Back
Top