Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi,
I am trying to use CC1101 IC to read UHF RFID tags at ~868MHz. I have only seen EPC gen 2 Class 1 rfid tags for that range. Can I use CC1101 transceiver to read those tags? If not can I read any sort of RFID tags using this chip?
Looking forward to your replies. Thanks a lot in advance.
Which RFID reader are you using? I am looking for a cheap RFID tag reader that works at least for 1 meter range. Can anyone suggest any modules??
Thanks
Hi,
I want to interface LinkIt Connect 7681 with another board that provides SPI interface. In the API description of LinkIt Connect it is written that the SPI interface provided can be used to interface a 1MB flash memory with the board there is no information about whether it can be used as a...
Hi,
I tried to compile microchip's TCPIP stack version 5.36.4 with my hardware containing 18f4620+ENC28j60.... But I am having troubles with it.... It gives me error that says:
C:\Microchip Solutions v2011-10-18\Microchip\TCPIP Stack\ENC28J60.c:208:Error [1105] symbol 'SSP1CON1' has not been...
yes finally it's working... as soon I got 12v Vpp it started working fine... It was the inductor that was damaged... phew huge disaster it brought, wasting my time..... BTW thanks to you guys for your patience and advices... thank you very much..
tried these above suggestions as well... but no difference on Vpp voltage... I can not get the point how can Vpp be 12 volts when usb port supplies only 5 volts...
another thing won't 12 volts damage my controller..
I think my circuit is working except that 12 volt part... So can you tell me...
no R4 and R5 are in right positions... here is voltage drop on R5 at different positions..
1. at normal position (MCLR off)... 3.58 volts
2. when Vpp tested to be 12.0 volts it is 4.47..
3. and when MCLR on it is 2.98 volts....
while total drop on voltage divider R4 and R5 is 5.23 volts....
Here I am with these results while troubleshooting....
1. external Vdd detected... (which is not a problem as you guys said)..
2. Vpp -- the software shows it to be 12.00volts.. but there is not a single point on my circuit where voltage crosses 5.38 volts when checked using a multimeter...
ignoring all those errors if I try to detect my other 18f2550 connected to pickit2 I gives me error "No device detected".... Why is that so........
---------- Post added at 20:59 ---------- Previous post was at 20:47 ----------
I checked for R3 no break or dry solder...
and Q1 replaced still...
1. when testing Vdd it gives "An external voltage was detected on the Vdd pin at 5.0 volts" however I have no external circuit connected to its output.
2. For Vpp test the software shows 12.0volts while on ICSP conn I receive 5.0 volts...
aahaa... I finally got rid of that jamming issue.... now I am able to open Pickit2 V2.61 and it shows Pickit2 found... But there is another problem now... It shows me Vpp and VDD error when I try to program.... How should I remove this bug....
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
