Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi friends,
I am using STM32F103RB for debugging my custom board(SWD). i was doing my debugging successfully,
But now i got an error i could not debug. below i mention the error.
Error: Error in final launch sequence Failed to execute MI command: load...
Hi, I am using STM32F103VBT6 micro controller, i have done a RTC code for date and time,
But in that, I need to do a interrupt for every 1 minute. Is it possible to do?
I have done some code, for interrupt .
but its not working.
How can i do interrupt for every 1 minute from RTC?
controller has...
Hi,
I want to measure unidirectional only.
DC_Volt = 24V
Ref_in = 2.5V.
O/P is going to Micro Controller. I am using STM32F103RB.
Maximum I/P range is 3.3V.
So i used R45 is 1.5E.
This is is my circuit. Here I am using the 2 wire pressure Sensor, is Nah_8253 From Trafag - Ag. Here i Also use a comparator.
Here i am aiming to sense the high side current.
Is this circuit is correct or not.
Hi,
i want to convert 4 to 20mA into 0-3.3 v range.
I know about RCV420. but it needs negative supply.
Anyone knows any ICS, which is converting the current into voltage other than RCV420?
Thanks in Advance
Akhil francis
Hai,
my name is akhil francis.
I am using STM32F103R6 CONTROLLER. I am new to STM32 controllers.
i want to generate pwm outputs from the controller,
my doubt, is this controller has dedicated pin for the pwm generation.? or can we generate the pwm o/p through the any of the i/o pin
by...
Thanks for your reply.
I am using "FTP-628DSL490" interface board also with this thermal printer. I guess this interface board will convert the TTL level into rs232 level.
my controller has CTS, RTS pins instead of DTR and DSR.
my doubt is
what are the pins which i have to connect into this...
Hi,
Thanks for your reply. I am using "STM32F103R6" microcontroller.
while reading, my understanding is for serial i have to use 8 pins for connecting the "FTP-628DSL490 " interface board with
STM32F103R6 micro controller.
8 connections
1. RD
2 TD
3 DTR
4 GND
5 DSR
6 SLCTIN
7 INPRM
8...
FTP-628USL401 , this is the printer which i am going to use. i am planing to bring the interfacing board also.
I have the data sheet. but i need to know some theory about the operation. I am going to communicate with serial interface.
How the strobes and latch signal is working, how the stepper...
Hai,
I have a doubt about EDE1400 IC.
I read data sheet of this ic. I have attached the schematic of this IC with micro controller.
by doubt is there is no connection to stepper motor. how we control the stepper motor? or no need of
that?
And from where i could by this IC?
Please give...
Hai,
I am new to thermal printer. I am planing to interface fujitsu thermal printer with micro controller. In fujitsu data sheet i could not find anything more about code side. I dont know about the communication protocol between the printer and the micro controller.
For serial reading should i...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.