Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by ahmed_hussein144

  1. A

    Broadband ridged horn design

    yes , I changed the distance between Tx & Rx, the response is same mean the received signal using two feeds (case 3) is two time the received signal for one feed (case 1) at the same distance.
  2. A

    Looking for papers discussing ridged horn antenna design

    Hello biff44 Thank you very much for your answer. I fabricated a new double ridge horn antenna. As I mentioned that I have two signals which have same rise time and same fall time. The amplitude of these signals are same with different sign, for example first signal has amplitude of 30 V and...
  3. A

    Broadband ridged horn design

    Hello Abhishekabs, Thank you very much for your answer. I fabricated a new double ridge horn antenna. As I mentioned that I have two signals which have same rise time and same fall time. The amplitude of these signals are same with different sign, for example first signal has amplitude of 30 V...
  4. A

    Looking for papers discussing ridged horn antenna design

    Hello biff44, Actually, I want to apply two signals, these signals have same rise time and same fall time. The amplitude of these signals are same with different sign, for example first signal has amplitude of 10 V and the second has -10 V. The delay time between these signals is 0 second which...
  5. A

    Broadband ridged horn design

    Hello Abhishekabs, I tried to improve the isolations between ports based on the points that you told me, but I still have the problems (bad isolation between ports), therefore I send you the model of the antenna, maybe you can help me?. Thank you very much for your helping.
  6. A

    Looking for papers discussing ridged horn antenna design

    Hi, I am working on design double ridge horn antenna with two feed points, where The inner conductor of the first coaxial probe pass through the first ridge and is then connected to the opposite ridge. The shield of the coaxial probe is connected to the lower ridge. and the same thing for the...
  7. A

    Broadband ridged horn design

    I changed the positions of probs on the waveguide to improve the isolation between probs but I still have isolation around 5 dB
  8. A

    Broadband ridged horn design

    Hi, I am working on design double ridge horn antenna with two feed points, where The inner conductor of the first coaxial probe pass through the first ridge and is then connected to the opposite ridge. The shield of the coaxial probe is connected to the lower ridge. and the same thing for the...
  9. A

    Horn Antenna and radiation pattern

    radiation pattern horn antenna hi all, if there is some one can help me, I need example in HFSS to design Double ridge Horn Antenne,
  10. A

    Spiral antenna simulation in HFSS

    hi all, if there is some one can help me, I need example in HFSS to design Double ridge Horn Antenne,
  11. A

    how calculate input impedance in hfss 11?

    hfss impedance calculation hi all, if there is some one can help me, I need example in HFSS to design Double ridge Horn Antenne,
  12. A

    ANSOFT help: microstrip patch antenna-how and where to start

    ANSOFT help hi all, if there is some one can help me, I need example in HFSS to design Double ridge Horn Antenne,
  13. A

    Lumped port joining ansoft HFSS

    hi all, if there is some one can help me, I need example in HFSS to design Double ridge Horn Antenne,
  14. A

    Need HFSS tutorial on simulating high-impedance ground planes

    Tutorial hi all, if there is some one can help me, I need example in HFSS to design Double ridge Horn Antenne,
See more

Part and Inventory Search

Back
Top