Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by abhignans

  1. A

    how to add hex value into eeprom programatically in attiny85

    i am making a small home automation circuit to control a relay using ir remote. i want to make flexible by making it to use any remote for that i want to add hex data into eeprom from ir remote. and use it later use i want to add hex file programatically in attiny85.i want a procedure to how...
  2. A

    how to use a transistor instead of relay to drive 5v 2amps

    thanks for the speedy reply rajik i have tried it using a mosfet irf540 but there is a voltage drop from 5.5 to 4.6 which makes the circuit failure i need a bjt or mosfet with low or nill voltage drop can u please suggest me one
  3. A

    how to use a transistor instead of relay to drive 5v 2amps

    hello everyone i am trying to power a circuit using attiny85 and tsop taking input through ir remote the circuit consumes 5v and 2 amps currently i am driving it using a 5volt relay. i want to drive the circuit using a transistor i am confused which transistor to use instead of the relay...
  4. A

    remote control using ht12e with 12 switches

    hello everyone i am currently designing a remote control using ht12e i am able to control six switches using three io pins but i want 12 switches with 4 io pins as i can use 4 io pins of ht12e as data pins i want 12 switches to control these 4 io pins i cannot use any external ic or encoder...
  5. A

    nec protocol decoding in c for 89s52(8051)

    hello i want to decode nec format using 89s52 micro and i have develoed the code but im unable to get where is the problem. first thing i want to know is the code correct secondly can i have any c sample code to decode nec format using 89s52 ...if the code is using 89c2051 i will b gladfull...
  6. A

    Help Arduino Program

    for the solution of this u can use goto statement and let the arduino wait for command check this out i have rewritten the code with ur requirement void int() { val=digitalRead(pinB); // read data one: if(pinB == HIGH) { Serial.println("PINA ON"); //write serially goto two;} else...
  7. A

    how to drive high current 5 volts circuit using 89s52

    hello, i am using 89s52 micro controller to drive a individual circuit,.i.e i have to power a raspberry pie using 89s52. the raspberry needs 5 volts,1amp miniimum to power it i have used a relay to power it but in the cirvuit i have limitation for space so i have opted for mosfet IRF540 with...
  8. A

    Decoding TV IR Remote Control Signals (NEC) with MSP430?

    hello eaglemaster i want support to decode nec ir signals using 8051 can u please post the decoding code using 8051 please i am in a very urgent need please send me as soon as possible thank you
  9. A

    interfacing seven segment display

    thanks Mr. BradtheRad 74154 pulls only one segment to low at a time but for multiplexing i need all segments to low and the display which has to be changed shud b high....im little bit confused again:-?can u suggest me how to do it - - - Updated - - - yes tat's a good idea mr.jpsganesh but im...
  10. A

    interfacing seven segment display

    hello ,everyone. im doing a temparature display using pt100 and pic18f452. i am using 8 pt100 sensors, ie..8 channel inputs.. i want the temparature to be displayed on the seven segment displays so for that to do i need atleast 2 seven segment displays for each channel 1pt100 sensor=2 seven...
  11. A

    how to interface both RTC DS1307 and SD CARD to PIC18f452

    Hello all, im am trying to make a data logger to save temparature of 8 different places(i.e 8-channel) i have selected pic 18f452 so tat i have lot many pins to interface multiple seven segment display(say 16) i need to take the temparature inputs and display them on seven segment display and...
  12. A

    [SOLVED] Relay Problem with AT89s52

    instead of using an 10k resistor use this combination
  13. A

    the output of the microcontroller 89s52 is very low

    i am a begginer in embedde systems and i am trying to do a project firstly i have tried doing a circuit for blinking led the code works but the output coming from output pins is very low(abt 1.89volts) what may be the problem please reply me soon here's the schematic

Part and Inventory Search