# Activity Stream

• Today, 13:05
Sorry, Im wrong. Assume two solutions, y1(x) and y2(x). y3(x)=a1*y1(x)+a2*y2(x) also satisfies y3(x)=dy3(x)/dx
3 replies | 105 view(s)
• Today, 12:41
Your DE can be written as: y' = 2*x^2. It's of the first order because the maximum order of the derivative of "y" is 1. It's not homogenous...
3 replies | 105 view(s)
• Today, 12:32
Hi, I have successfully run a monte carlo (transient) and extracted the vth for each run (using the "finalOptime") option. Anyone know how to...
0 replies | 13 view(s)
• Today, 12:14
What is an "R-Core" transformer? We need to backtrack here - regardless of the advice that you don't need them, are you proposing snubbers across...
37 replies | 3493 view(s)
• Today, 11:48
You set the "SRTYPE" to either "SYNC" or "ASYNC" depending on the reset signal used in your design. E.g. - If you have a sync reset, then the ODDR...
3 replies | 93 view(s)
• Today, 10:38
Pressure of 1 kPa barely moves the needle on an everyday automotive vacuum gauge. This low pressure might be detected by the depth of liquid a hose...
3 replies | 215 view(s)
• Today, 10:11
I'm trying simulating my hffs file (.aedt format) on other computer, but this error message appears and can't progress on simulation. "Unknown...
0 replies | 38 view(s)
• Today, 10:08
Common mode feedback does not solve this. Common mode feedback solves mismatch between ID(M3)+ID(M4) and ID(M0). If there is a mismatch between...
6 replies | 155 view(s)
• Today, 10:03
thanks for quick reply. I have already seen this document. But I don't understand that suppose "SRTYPE" is ASYNC then what should be the values of...
3 replies | 93 view(s)
• Today, 09:36
As I also gonna use this Snubber for my DAC that has an R-Core transformer, with a total of five cables for secondary as follosing: 9-9, 15-0-15 VAC...
37 replies | 3493 view(s)
• Today, 09:10
Take a look at the ODDR for 7 series library guide....
3 replies | 93 view(s)
• Today, 08:59
Hello, I am currently doing my project which requires me to use DE1-SoC. The project is to perform bearing healths prognostic, it includes 3 parts...
0 replies | 44 view(s)
• Today, 08:26
hi, when we instantiate ODDR then how to provide value to "SRTYPE" and set/reset. I mean for "async" and "sync" in SRTYPE what should be the value...
3 replies | 93 view(s)
• Today, 08:25
Hi, I wanted to insert cell using script in innovus during eco. I intended to using ecoAddrepeater command for this, and wanted to add prefix for...
0 replies | 34 view(s)
• Today, 08:23
See how 2 MHz clock is derived from DDS MSB phase. You can generate 4 MHz in a similar way by utilizing phase too.
15 replies | 745 view(s)
• Today, 07:59
Thanks. Do you, or someone here, have this software? I would be interested in the following test : let's assume a 2 port network of S-parameters...
5 replies | 512 view(s)
• Today, 07:45
I have just corrected skid buffer implementation which should have been 2-entries FIFO See if you guys could find anything wrong with this skid...
28 replies | 1136 view(s)
• Today, 07:43
Hi, The linked site tells you everything you need to know. What additional information do you need? Klaus
4 replies | 427 view(s)
• Today, 07:38
Hi, Every Opamp manufacturer provides such documents. Start with the datasheet of the selected Opamp. Go to the manufacturer of the Opamp.. to...
68 replies | 1522 view(s)
• 3 replies | 105 view(s)
• Today, 06:59
Such conclusion is too strong and is wrong in general. The devil is in details, as usual. As long as distributed admittances around the structure...
12 replies | 335 view(s)
More Activity