Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Voltage Rating on SuperCapacitors

Status
Not open for further replies.

ste2006

Advanced Member level 4
Full Member level 1
Joined
May 1, 2012
Messages
118
Helped
3
Reputation
6
Reaction score
3
Trophy points
1,298
Activity points
2,226
Hi,

This is probably a simple question but a little experience or advice would be great. I am designing a new system using a micro-controller and a few other bits but it turns out to battery back up the RTCC and nothing else is quite tricky and it is probably simpler and cheaper to just use a separate RTCC chip.

With this in mind i am going to use the AB8013 chip which has provision to charge a backup source with automatic switch-over if the main power fails.

I am currently looking at super capacitors for this purpose but i am not sure what voltage i need. All of the super capacitors seem to be rated quite low. The circuit itself is using 3.3V so is a 3.3V Super Capacitor acceptable?

Normally for an electrolytic capacitor i would give lots of margin on the voltage but to do that here i would have to put two of these capacitors in series and i don't have the board space.

I read elsewhere that normally super capacitors can be used at their rated voltage no problem,

Any thoughts??

Thanks,
 

Super capacitor individual cells are rated 2.5v.
Therefore a very common configuration is two cells in series, for 5 volts. Use such a device.

A question: who makes the AB8013 chip? I could not find its data sheet.
 

Super capacitor individual cells are rated 2.5v.
Therefore a very common configuration is two cells in series, for 5 volts. Use such a device.

A question: who makes the AB8013 chip? I could not find its data sheet.

You see i am very limited for space and i have found a 3.3V rated Super Cap
https://ie.mouser.com/ProductDetail...GAEpiMZZMuDCPMZUZ%2bYlx/EpfZdXAvqhE5Pkm/ul9I=

Data sheet for the chip is here
https://www.mouser.com/ds/2/3/AB08XX-47355.pdf

Looks a lovely chip to be honest

Any further thoughts would be great but i think i will go with this capacitor
 

That is a ceramic super cap!
This is New technology, it is not the more common aerogel technology.
Yes, go for it.
 
That is a ceramic super cap!
This is New technology, it is not the more common aerogel technology.
Yes, go for it.

Ah very good, I was thinking it was very small and an odd voltage alright,

Thanks for the help
 

The ceramic "supercap" is quite nice. But even with very low current consumption of the Abracon RTC, it will provide backup only for a few days. That may be too short for many applications.

The Abracon RTC doesn't recharge the capacitor, you need an external low leakage diode.
 

The ceramic "supercap" is quite nice. But even with very low current consumption of the Abracon RTC, it will provide backup only for a few days. That may be too short for many applications.

The Abracon RTC doesn't recharge the capacitor, you need an external low leakage diode.

If you refer to the application notes, Section 5.15 you will see it has a trickle charger built in to it,

https://www.abracon.com/Support/AppsManuals/Precisiontiming/AB08XX-Application-Manual.pdf

I only need the clock to back up for a few hours in the event of a power cut so size is no problem,

Thanks,
 
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top