Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

EasyPIC 3 Dev Board Schematic

Status
Not open for further replies.

skhimsara

Newbie level 1
Joined
Aug 20, 2005
Messages
1
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,307
easypic3 schematic

Hi

can anyome please give me the Easy PIC 3 schematic.
I need it for my project in PIC .
i am an elec engg student doing my final year project

thanks in advance
 

easypic3

Hi, Dearfriend

By the way, I am electronics eng then I want the Schematic for EasyPic 3 or 4 if you have it please let me know

Kind Regards

Hassan
 

easypic 6

i think trying to make a hardwar such as easy pic3 will be more expensive than getting the board itself. i might be wrong but i am sure making easy PIC3 is not your project. if u need to use a devlopment board try and get one, and you will get some additional package with it alongside. but if you need a do it yourself try the oshonsoft develoment board and other ones you can get online.
 

easypic 5 schematic

The easyPIC boards would be a nightmare to hand wire. And I'm sure they don't publish the layout artwork.
 

pic board schematic

Schematics are easy to design. It's the layouts which take skill.

No one will ever give out his layout for a commercial board.
 

easypic4 schematic

I have got the easypic 3 and 4 schematics some where but to be honest just buy one well worth the money, I tried to make one but gave up

the on-board programmer/debugger can't be copied anyway so what's the point without those you may aswell design a simple one jut to a 40pin board and then adpators to plug into the 40pin board so simple

wizpic
 

easypic 3

i had have saw it in this site.
could you see schematics in this directory
**broken link removed**
 
Last edited by a moderator:

easypic schematic

wizpic said:
I have got the easypic 3 and 4 schematics some where but to be honest just buy one well worth the money, I tried to make one but gave up

the on-board programmer/debugger can't be copied anyway so what's the point without those you may aswell design a simple one jut to a 40pin board and then adpators to plug into the 40pin board so simple

wizpic

My MPLAB ICD2 clone can be built, and the Firefly & Unicorn kits too. I publish the schematics and .hex files required for my kits.

You can even do USB with the Unicorns 18F4550 (GLCD & LCD too)
The picture below was done by a Unicorn user.
 

pic board schema

Bueroomelectronics i was talking about the easypic 4 board which has it's own built in programmer/Debugger and that bit cannot be copied,

Yeah your kits look good and simple to build

wizpic
 

easypic 6 development board

have anywone make a clone ?

sorry for my bad english
 

easypic, 18f4550

I have a damaged Easypic3.The problem is that it recognises all mcu's as 12f508. The board gets detected by computer and usb connection is established. Any help
 

easy pic 3 schematics

The 12F508 does not have an on chip ID nor does any 12bit core PIC. Sounds like it sees nothing at all.
What are the IC part numbers on the EasyPIC3 programmer section?
 

easy pic usb programmer built

this looks nice gonna try to toner transfer it and see if i can play with it some. This is a great board, I am new but it seems GREAT!!!!
 

easypic3 circuit

easyPIC 4 has been established,does anyone get it?
 

easypic 6 manual

HI FRIENDS
IS SOMEBODY INTERESTING IN A SIMILAR DEVELOPMENT BOARD LIKE EASYPIC4.
DIFERENCE IS WHAT IT WORKS WITH MPLAB OR PICKIT2, THE PROGRAMMER IS COMPATIBLE WITH PICKIT2
WE MADE ONE, AND WE ARE GOING TO PRODUCE FOR SELL. YOU CAN SEE A PICTURE IN THE NEXT LINK
 
Last edited by a moderator:

easypic compatible programmer

I made my own dev board for PIC18F4520. It's more or less like EasyPIC4. There is an on-board MPLAB 7.60a compatible ICD2 (upper right corner). Yesterday I demonstrated this board as my final work for bachelor's degree. It works but still needs a lot of improvements. The board features a lot of perphereals, like I2C (for eeprom), SPI (for MAX7219), OneWire (for DS1820), RS232 (MAX232), analog input (two potentiometers), socket for resonator, piezo buzzer, two connectors for LCD 2x16 and GLCD 128x64, pull-up/down resistors, push buttons, LED's, each port has a connector for external devices. Each device can be connected/disconnected with a dip switch or a jumper (like in EasyPIC's).

I could publish the schematics and all but I wont, coz the design is not perfect yet. It will be (I hope) after summer :)

 

2 easypic3 connection i2c examples

dgs117, I look forward to seeing your end result. I also want to make a board like that myself.
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top