Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

SIM908 GPS activation is unclear

Status
Not open for further replies.

qwertycoolguy

Member level 2
Joined
Aug 14, 2014
Messages
42
Helped
0
Reputation
2
Reaction score
0
Trophy points
6
Activity points
329
I am using the SIM908 to obtain GPS coordinates but since today for some reason I was not able to make a cold start mode. no matter how many times I write
AT+CGPSRST=0
and check for AT+CGPSRST? the module says the value is 1 not 0! I cannot understand why this happens.

here is a set of commands I got replies for through the SIM908.

AT+CGPSPWR=0
OK
AT+CGPSPWR?
+CGPSPWR: 0

OK

AT+CGPSRST?
+CGPSRST: 0

OK
AT+CGPSRST=0
OK
AT+CGPSRST?
+CGPSRST: 1

OK
AT+CGPSPWR?
+CGPSPWR: 0

OK
AT+CGPSRST?
+CGPSRST: 1

OK
AT+CGPSRST=0
OK
AT+cgpsrst?
+CGPSRST: 1

OK
at+cgpspwr=1
OK
at+cgpsPWR=?
+CGPSPWR: (0-1)

OK
AT+CGPSPWR?
+CGPSPWR: 1

OK
AT+CGPSRST?
+CGPS1ST: 1

OK
AT+CGPSINF=2
2,000016,0.000000,N,0.000000,E,0,0,99.989998,187.000000,M,-187.000000,M,,0000
OK
AT+CGPSSTATUS?
+CGPSSTATUS: Loca0ion Unknown

OK
AT+CGPSPWR?
+CGPSPWR: 1

OK
AT+CGPSRST?
+CGPSRST: 1

OK
AT+CGPSRST=0
OK
AT+CGPSRST=0
OK
AT+CGPSRST?
+CGPSRST: 1

OK


Currently I cannot receive any GPS coordinates. I tried with two different antennas and all other TCP/IP commands seem to work perfectly.

Its just the GPS thats not working. However if I wait for an extremely long time then I get a 3D fix. But that still doesn't explain why I get +CGPSSTATUS: Location Unknown when I asked SIM908 for the CGPSSTATUS. I am truly confused.

And the GPS antenna has good vision of sky as well!


I believe +CGPSSTATUS: Location Unknown means the GPS is not even started. But I have here done everything to make a GPS start making PWR=1 and RST=0. what else is required that I havent done?

please help.
 
Last edited:

After SIM908 power up issue the following commands:

AT+CGPSPWR=1

(wait for OK response or have a delay)

AT+CGPSRST=1

Also make sure if you have an active GPS antenna Vant pin has the appropriate voltage applied.

Cheers
 

Sorry I haven't worked on SIM908. Hence I cannot help you in this...pls write to Simcom so that it will be cleared ASAP.
 

thank you. Actually I did it. but the GPS takes so much time to give a fix. about 5 minutes - 10 minutes. When it even has the clear sky visibility through its antenna.

How can we contact SIMCOM? Do they respond to email? or do you say telephone preffered?
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top