Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

How to build a 100 volt power supply?

Status
Not open for further replies.
C

coppils7

Newbie level 2
Joined
Jan 26, 2012
Messages
2
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,303
Hello,
I need a power supply which outputs 100 volt DC, and at least about 10-50mA. Preferably it would be variable from 0-100 volts (in steps of 5 or 10 volts is totally ok, and if it is quite simple I don't need it to be variable, I can build a few with different output). I have 230v AC mains, should it be done with a transformer and rectifier and something more, or would it be easier to step-up for example 12 or 24 volt DC? Is it possible to use an op-amp to step up voltage to 100 VDC? I would maybe prefer to step-up a lower DC voltage, but anything is okay.
 

Dear Coppils
Hi
As i understood , you wanna build a 0-100v variable power supply with 50ma current. so you can use a series ceramic capacitor with the power line and then you can rectify it and ...... BTW , i think if this supply be not isolated , it will be harmful and dangerous , and if you are beginner , i suggest you , don't try to do it , because it is dangerous . but you can do it with switching systems , or a simple low current transformer ( 230/110).
Best Wishes
Goldsmith
 

Get a variac with a 1:1 transformer for protection and a fullwave rectifier to make DC.
 

Dear klystron
Hi
AS i know , the variacs are based on auto transformers , what are not isolated.
Respectfully
Goldsmith
 

I agree with Goldsmith, that is why I sugested a 1:1 isolation transformer for protection (see my post) The 1:1 transformer is on the output of the variac.
 

Having no mains isolation in supplies is QUITE DANGEROUS. The best safe method is use as Isolated Transformer and a Rectifier. For making it variable a controlled Thyristor circuit can be used in the Primary Side.
 

Would it work to use a regular "house lamp dimmer" for 230VAC and then rectify it's output? That would be simple, but would it work? And is it possible to use a 230v -> 110V conversion transformer instead of an isolation transformer, as they are quite expensive? I mean a transformer that is used for using 110V devices from 230V..

If I don't need it to be variable, would there be some easy way to build it?
 

Again HI
Yes it is possible . but you should filter it correctly and you should use EMI before that to prevent from harmonics interference . and again it will has hazard for your health ( because it is not insulated)
Best Lucks
Goldsmith
 

Mains AC can be dropped to a lower voltage by inserting a capacitor. It's useful when you only need small current, as with lighting an led.

Example, this link:

Marc's Technical Pages: Mains LED

A diode bridge will convert to DC output.

It may be hard to get exactly 100V. If you have a particular load then you must experiment to find the particular value of capacitor to give 100 V.

Or you can use a zener diode, or several in series, to regulate to 100V.

----------

If you don't wish to use mains power, then a DC supply can be stepped up using a switch mode DC-to-DC converter, containing an inductor.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top