Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

RAM Limitation Problem in HFSS 13

Status
Not open for further replies.

bekushal

Newbie level 3
Joined
Jan 20, 2012
Messages
3
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Location
Jodhpur, India
Activity points
1,308
I have i5 processor and 16GB DDR3 RAM in my system, still it shows execution error message to do check the DESIRE and MAXIMUM RAM limitation. I tried many times to solve this by changing those limitation values. I am a beginner so please help me out in this. Earlier it took very less time for simulate the same model, but now it either terminated or gives an error of RAM limitation.
Please Help me:-|...
 

Bekusal, I think you have 32-bit operating system in you computer. A 32 bit OS can only use 4GB of memory total. Although you have 16GB RAM but that is not fully used.
**broken link removed**
 

Bekusal, I think you have 32-bit operating system in you computer. A 32 bit OS can only use 4GB of memory total. Although you have 16GB RAM but that is not fully used.
**broken link removed**

@Yadav, thank you sir for reply..
Sir i have already gone through this thing, this is an 64 bit os and it is using complete 16GB of main memory.
As i heard recently about the solution of this problem, that can be solve by choosing the DESIRE RAM limitation, because hfss performs swapping on its own, without rely on an OS. According to this i have changed my temp folder location to the 100GB vacant partition of my pc, because that space and available main memory decides the execution boundaries.
But i still dont know what exact values should i use..
help me out... :???:

---------- Post added at 16:18 ---------- Previous post was at 15:31 ----------

any buddy from great edaboard members, who has good hands on hfss or antenna designing, please drop your contact detail to private message box. This is a humble request from an unaided student..
please help..
 

I have i5 processor and 16GB DDR3 RAM in my system, still it shows execution error message to do check the DESIRE and MAXIMUM RAM limitation. I tried many times to solve this by changing those limitation values. I am a beginner so please help me out in this. Earlier it took very less time for simulate the same model, but now it either terminated or gives an error of RAM limitation.
Please Help me:-|...

I would tend to leave those at the default 0, which is unlimited. Have you looked in hfss to see how much ram is being used. You can get it somewhere on the "HFSS" menu of "HFSS". You can get real-time information on the convergence, RAM usage etc. I forget exactly where it is, and don't have HFSS on a machine close by.

Can you post the file.
 

I would tend to leave those at the default 0, which is unlimited. Have you looked in hfss to see how much ram is being used. You can get it somewhere on the "HFSS" menu of "HFSS". You can get real-time information on the convergence, RAM usage etc. I forget exactly where it is, and don't have HFSS on a machine close by.

Can you post the file.

Thank you DEBORA.HARRY Sir,
i have attached a snapshot, please analyse this, i hope this will be helpful for us to understand the problem.
Now one thing that i seen the same model with small dimensions get simulates but as i increase the parameters it shows an error "Metrix solver exception: out of disk space" :???:

Image
 

It appears that this simulation is HUGE! The first pass is already trying to swap onto the harddrive. It may be best for you to post your project as it may not be set up ideally

Have Fun
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top