---
+ Post New Thread
Results 1 to 5 of 5
  1. #1
    Advanced Member level 2
    Points: 3,992, Level: 14
    Mithun_K_Das's Avatar
    Join Date
    Apr 2010
    Location
    Dhaka, Bangladesh, Bangladesh
    Posts
    606
    Helped
    13 / 13
    Points
    3,992
    Level
    14

    problem with IR2110 and DC/AC converter portion of sine wave inverter

    I'm trying to design a sine wave inverter based on Switch Mode technology. I tried many circuits. each of them creating problem. now the latest one was like this:

    sfsafsafas.png

    Mosfets are protected via that fuse from burning. I am using 1A fuse there. Fuse is burning again and again. I don't know why. I fetched this same problem before but found no solution.

    MCU pic16f73 is generating two PWM signals like:
    fvav.png

    what is the problem and what is the solution?


    again I tried with another one. But in that circuit NE556 is not generating any clock pulses. I checked PCB diagram again and again, but still can't find then ans. But the DC/DC converter portion is working fine.

    the circuit is:
    12v-220v-invertor-sinus-ferit-trafo-nuve.gif

    and my DC/AC converter portion is:
    vasfsfwafews.png


    Now the question is why all these faults happening???

    •   Alt28th November 2011, 09:24

      advertising

        
       

  2. #2
    Advanced Member level 4
    Points: 11,805, Level: 26
    ALERTLINKS's Avatar
    Join Date
    Dec 2003
    Location
    Pakistan
    Posts
    1,164
    Helped
    350 / 350
    Points
    11,805
    Level
    26

    Re: problem with IR2110 and DC/AC converter portion of sine wave inverter

    The circuit of 556 has a input from 315V but it is only connected to ground. This is a apparent fault in circuit diagram, there may be others. Can you show circuit diagram of inverter using MCU pic16f73?



    •   Alt28th November 2011, 16:05

      advertising

        
       

  3. #3
    Advanced Member level 2
    Points: 3,992, Level: 14
    Mithun_K_Das's Avatar
    Join Date
    Apr 2010
    Location
    Dhaka, Bangladesh, Bangladesh
    Posts
    606
    Helped
    13 / 13
    Points
    3,992
    Level
    14

    Re: problem with IR2110 and DC/AC converter portion of sine wave inverter

    that +315V is connected to pin 12&13 of NE556 via 1M+470K+470K||(500KVR+33K). and the circuit diagram of the inverter with PIC16f73 is the first one post.


    My question is what is the frequency in first stage DC/DC converter (with KA3525) ? and then what should be the intial frequency of PWM to generate 50Hz sine wave in the next stage?????
    Last edited by Mithun_K_Das; 29th November 2011 at 10:46.



    •   Alt29th November 2011, 03:22

      advertising

        
       

  4. #4
    Advanced Member level 4
    Points: 11,805, Level: 26
    ALERTLINKS's Avatar
    Join Date
    Dec 2003
    Location
    Pakistan
    Posts
    1,164
    Helped
    350 / 350
    Points
    11,805
    Level
    26

    Re: problem with IR2110 and DC/AC converter portion of sine wave inverter

    I dont see circuit diagram of 1st inverter. Its only the PCB design. Frequncy is determined by Rt on pin 6 and Ct on pin 5 of 3525 ic. Here it is 39k(R7) and 1n (C5) are shown.It will be around 35KHz.



  5. #5
    Advanced Member level 2
    Points: 3,992, Level: 14
    Mithun_K_Das's Avatar
    Join Date
    Apr 2010
    Location
    Dhaka, Bangladesh, Bangladesh
    Posts
    606
    Helped
    13 / 13
    Points
    3,992
    Level
    14

    Re: problem with IR2110 and DC/AC converter portion of sine wave inverter

    No, Its 22KHz.



+ Post New Thread
Please login