---
+ Post New Thread
Results 1 to 7 of 7
  1. #1
    Newbie level 3
    Points: 299, Level: 3

    Join Date
    May 2011
    Posts
    3
    Helped
    0 / 0
    Points
    299
    Level
    3

    How to choose a diode in a rectifier circuit ?

    Hi

    On diodes datasheets there is a rating value called "the rectified average current (Io), what this value mean ? how to calculate it ?
    - How to choose the diodes for use in a rectifier circuit depending of Io ?
    - How to calculate the value of (Io) if i use for example a simple power supply : a transformer with 9v rms secondary voltage + bridge rectifier + 6800uF capacitor + load (maximum load current 250 mA)

    sorry for my english..

    •   Alt9th May 2011, 23:12

      advertising

        
       

  2. #2
    Advanced Member level 1
    Points: 3,875, Level: 14

    Join Date
    Mar 2006
    Location
    Culiacán, Sinaloa, Mexico
    Posts
    479
    Helped
    68 / 68
    Points
    3,875
    Level
    14

    Re: How to choose a diode in a rectifier circuit ?

    The selection of the diode is based on the peak current and average.
    For a full wave rectified sinusoidal id 0.637 the peak value.
    Bot the average and peak current must be below the values indicated in the datasheets of the diode.
    For the transfoemer you need to specify the it's power .



  3. #3
    Full Member level 2
    Points: 1,579, Level: 9

    Join Date
    Jul 2009
    Location
    chennai
    Posts
    123
    Helped
    15 / 15
    Points
    1,579
    Level
    9

    Re: How to choose a diode in a rectifier circuit ?

    Plz go threw this links... it may usefull to you for study about powersupplys & Diodes....

    Power Supplies

    How to choose the correct diode?

    http://www.egr.msu.edu/classes/ece48...on%20Note2.pdf
    Senthilkumar.


    1 members found this post helpful.

    •   Alt10th May 2011, 10:01

      advertising

        
       

  4. #4
    Newbie level 3
    Points: 299, Level: 3

    Join Date
    May 2011
    Posts
    3
    Helped
    0 / 0
    Points
    299
    Level
    3

    Re: How to choose a diode in a rectifier circuit ?

    thx but anyone can tell me How to calculate the value of (Io) ? if i use for example a simple power supply : a transformer with 9v rms secondary voltage + bridge rectifier + 6800uF capacitor + load (maximum load current 250 mA)

    is it equal approximately to Uc/Rload ?

    (Uc = Vpeak = 9 *√2]



  5. #5
    Super Moderator
    Points: 27,350, Level: 40

    Join Date
    Apr 2011
    Location
    Minneapolis, Minnesota, USA
    Posts
    5,585
    Helped
    1377 / 1377
    Points
    27,350
    Level
    40

    Re: How to choose a diode in a rectifier circuit ?

    In operation the average current through each diode will be your load current. But that's average.

    In detail... during a cycle each diode must carry a brief pulse which is much higher than your load current. So your diodes really ought to be rated higher than your load current.

    Not only that, power-up causes large surges to go through the capacitor because it is like a dead short when it is not charged. So your diodes must endure overcurrent for a few cycles.

    You probably can get by with 1A diodes rated for reverse 50V. This is a common 1N4001. Or use a bridge rectifier with the same rating.

    If one diode burns up, then you should replace all with 3A rating.


    1 members found this post helpful.

  6. #6
    Newbie level 3
    Points: 299, Level: 3

    Join Date
    May 2011
    Posts
    3
    Helped
    0 / 0
    Points
    299
    Level
    3

    Re: How to choose a diode in a rectifier circuit ?

    thx BradtheRad..i knew all that but what i really want is how to calculate this average current ?
    any formula or link that show calculation will be great



  7. #7
    Newbie level 1
    Points: 153, Level: 2

    Join Date
    Mar 2012
    Posts
    1
    Helped
    0 / 0
    Points
    153
    Level
    2

    Re: How to choose a diode in a rectifier circuit ?

    Can i know some practical schottky diodes for rectifier at 5Watt level



+ Post New Thread
Please login