Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Help ATMEGA 32 Programmer........

Status
Not open for further replies.
nikhilsigma

nikhilsigma

Full Member level 2
Joined
Jun 19, 2010
Messages
142
Helped
17
Reputation
34
Reaction score
16
Trophy points
1,298
Location
Delhi, India
Activity points
2,584
please help me the ATMEGA 32 programmer..........

USB programmer would be prefered............

please help me........

and also how actually programming occurs.......in a microcontroller........

thanking you
Nikhil
 

I am new to embedded......
and i want to make a programmer for ATMEGA32.......
and it would be great if it works for AT89s51....

and from the discussion( on the above link ), can figure out that my requirements are met by this programmer.....

but i am not able to understand that....WHAT TO DO ??


Can anyone of you be so kind to Please help me step by step what to do............

which circuit i have to make( there is a circuit on the above link &* also their is circit at https://www.fischl.de/usbasp/ ) & what are the unmentioned components in it..........

PLEASE HELP ME !!

I would be very thankful to you....
Nikhil
 

nikhilsigma said:
I am new to embedded......
and i want to make a programmer for ATMEGA32.......
and it would be great if it works for AT89s51....
and from the discussion( on the above link ), can figure out that my requirements are met by this programmer.....
but i am not able to understand that....WHAT TO DO ??
Can anyone of you be so kind to Please help me step by step what to do............
which circuit i have to make( there is a circuit on the above link &* also their is circit at https://www.fischl.de/usbasp/ ) & what are the unmentioned components in it..........
PLEASE HELP ME !!
I would be very thankful to you....
Nikhil
Click to expand...

Have a look at this thread where we have discussions about the USB ASP as it may be modified to program 89Sxx chips too.

Cheers
 

i have gone through it.......

but i have not found where to start exactly...

so will you kindly tell me.........
where to start from......
and what further steps i should take......
step by step......

just mention points, don't explain, rest i will handle...

Thanking you
Nikhil

Added after 1 hours 25 minutes:

Two questions...

1. whichv circuit i have too fabricate
**broken link removed**

or

https://www.fischl.de/usbasp/

2. how would i program ATMEGA 8 ??
3. What to do with the jumpers j1 j2 n j3...
 

for programming atmega8 you can use pony prog software and this circuit
 

Attachments

  • avr_programmer_schematic_6977.jpg
    avr_programmer_schematic_6977.jpg
    14.9 KB · Views: 144

What is the self programming jumper on the usbasp circuit.....

n also plz.. tell me how to program through computer....
i mean by which application...n how...
 

i don't know about self programming but you can programme thru * AVRDUDE supports USBasp since version 5.2.
* BASCOM-AVR supports USBasp since version 1.11.9.6.
* Khazama AVR Programmer is a Windows XP/Vista GUI application for USBasp and avrdude.
* eXtreme Burner - AVR is a Windows GUI Software for USBasp based USB AVR programmers.

Added after 49 minutes:

you can fabricate no 1 circuit that would be easy
 

hey in fischl.de/usbasp/ circuit is given only for atmega 8 ..where cani get the circuit for atmega 32? ..

to the circuit u mentioned first what are j1 j2 n j3?
will this seriously work for atmega 32?
 

The programming part of micro controller is fully depend upon the register....to program any microcontroller you need these things
1.development board
2.programming or compiler software like keil
3.software for feeding program in MC....
this is the basic needs and search Google you get everything related to MC
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top