Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

HFSS v12 error: Failure reading file for mode

Status
Not open for further replies.

nathj72

Newbie level 6
Joined
Jul 22, 2008
Messages
14
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,392
I get an the following errors:
Adaptive solution setup, process hf3d error: Failure reading file for mode=(gives a mode number eg. 5)

right after the above error I get this one:
Unable to create child process: hf3d.

HFSS v12.0.0 is being ran on windows server 2008 enterprise edition.

Does anyone know how to fix this error?
 

Strange. I am getting "Failure reading file for mode = 4" "Unexpected internal software error code 0 with module id 0" in ver.13 when using Eigenmode solver.
In the past I have rarely used Eigenmode solver, and when used, I never seen this behavior.
So, what could be the cause of the error?
 

I do not remember what I did to get around this problem anymore. I posted that question back in 2009. I was new to HFSS at the time and I would guess I probably just set something up incorrectly. I do suggest if everything fails, try redoing the simulation from the start (do not copy and paste anything).
 

I found that this happens when using PML.
But I was using PML before and don't see the difference.

...recreating the model from the scratch...I should hang myself も(x_x)
 

Are you sure the PML is far enough away from the resonant structure to not significantly affect the results. Try a PEC boundary condition instead of the PML and make sure the simulation runs fine. This boundary should perturb the results slightly, but you can still make sure it works.
 

Hello,

I used to get this error all the time before upgrading to HFSS 15. It occurred when trying to solve for modes which were spaced very far apart (in frequency). Try solving for a smaller number of modes, then create a new setup which solves for the remaining higher frequency modes.

Good Luck
 

nathj72:
My structure is not exactly resonant. It is periodic. PEC or PMC will surely give wrong waveguide modes which will destructively affect actual modes. PML is exactly what I need, but it crashes somehow.

In the past I had been trying a closed rectangular waveguide (PEC) or simple periodic objects in open-space (4 sides PML). And it was working fine.
Now I am simulating a periodic multilayer microstrip circuit and it crashes. Only when PML is created. I use PML wizard.

PlanarMetamaterials:
Thanks for suggestion! :thumbsup: I will try to pinpoint each mode selectively. Though, it is not very convenient...
 

The issue PlanarMetamaterials mentioned is an issue I had ran into, I just did not remember the error message. You do not need to do each mode individually, just less modes.

If you are trying to simulate a periodic structure (and want to generate beta-omega diagrams) you probably want it setup like this http://www.emtalk.com/tut_3.htm or this one http://www.emtalk.com/tut_2.htm.

If you want to extract the effective properties of the the metamaterial you will want try something like that given here **broken link removed**. This edaboard thread has more on it https://www.edaboard.com/threads/166956/.

PML is an artificial material which is matched to free space and is extremely lossy. If too many of your boundary conditions are this material the eigenmode solver will likely not converge.
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top