Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

DC Analysis for Bias circuit

Status
Not open for further replies.
W

wael_wael

Full Member level 4
Joined
Dec 3, 2005
Messages
221
Helped
5
Reputation
10
Reaction score
2
Trophy points
1,298
Activity points
2,760
Hi everybody

could some one help me to find out DC analysis for the following circuit for
examble, VDD= vdsat9 + vdsat10 +vdsat16 +vgs9 (correct me if i am mistake) but i need it for each branch
thanks in advanced

best regards
 
Last edited by a moderator:

hi
you are mistake
M16 is current mirror so we have current of M16 so we have |Vgs9| and so we have PCS3 and vice versa if we have PCS3 we have ID9 and Vgs16.
regards
 

    W

    wael_wael

    Points: 2
    Helpful Answer Positive Rating
VDD=vds9+vds10+vds16=vds16+vgs9
 

    W

    wael_wael

    Points: 2
    Helpful Answer Positive Rating
Thank you so much, now more clear for me
but i have 1 q more
that if we look to first branch frome the left side we cane see that
vdd=vdsat12+vdsat13+vdsat18
1.5=0.065+0.065+0.05
could u explain to me that
with my regards
 

Hi
assume
Id=0.5*beta*(Vgs-Vt)^2 (saturation)
so if draw Id vs. Vds we can find that for Vds> Vds(sat)
Id is Constant.
so in sat. region for specific Id and Vgs we can have any Vds that Vds> Vds(sat).
so we don't know Vds but we know Id and Vgs of each Transistor.
so
I know current of M18 (Id18) then I know Vgs12
=> Vds18=Vdd-|Vgs12|

regards
 

    W

    wael_wael

    Points: 2
    Helpful Answer Positive Rating
Thank u so much, you are very helpful, let me also thank our fourm also.

but i still have that equestion could u calculate the volts in the mentiond branch
thank you
regds
 

VDD=Vds12+Vds13+Vds18=vgs12+Vds18

If choose the voltege of PCAS PCS2 properly, we can make Vdsat12<Vds12 and Vdsat13<Vds13 to keep mosfets in saturation region.
 

    W

    wael_wael

    Points: 2
    Helpful Answer Positive Rating
thank i hope i got it rite,
bcz 0.065+0.065+0.05=0.18
but i will consider the second part of equation
vdd=vds18+vgs12
regards

Added after 2 hours 37 minutes:

Hi
could some one help to calculate v in the branches
i will be thankful so much.
regards
 

wael_wael said:
0.065+0.065+0.05=0.18
Click to expand...
Hi
I think that you have a basic mistake.
how you find Vds12 and Vds13?
you can not find Vds12 nad Vds13.
as I told in sat. region for specific Id and Vgs we can have any Vds that Vds> Vds(sat).
so you must just use Vgs to find each voltage.
for example Vds18=Vdd-|Vgs12|
but VICM=vdd-|Vds9|
in this case we must have Vds9 or we must use simulator or this equation:
Id=0.5*beta*(Vgs-Vt)^2 * (1+lambda*Vds)

regards
 

    W

    wael_wael

    Points: 2
    Helpful Answer Positive Rating
thank you so mush, i have no basic in this area
any way i am so chy from my question but better if i don't know ask some one.

so i got the values from the figure above you can see that, but i am not sure those values are VDS
thanx
regards
 

Hi
I don't know what are the numbers in figure. (may be W/L)
what is this figure?
regards
 

i am very sur the number is volt of Transistors, this one is Bias circuit for OTA
regds
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top