Can any one share max31865 RTD (PT1000) libraries for stm32?

Code C - [expand]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
/* SPI TIMEOUT Value*/
  #define TIMEOUT_VAL                 60
 
 /* Read Register Address */
 #define REG_CONFIG                  0x00
 #define REG_RTD_MSB                 0x01
 #define REG_RTD_LSB                 0x02
 #define REG_HIGH_FAULT_THR_MSB      0x03
 #define REG_HIGH_FAULT_THR_LSB      0x04
 #define REG_LOW_FAULT_THR_MSB       0x05
 #define REG_LOW_FAULT_THR_LSB       0x06
 #define REG_FAULT_STATUS            0x07
 #define WR(reg)                 ( (reg) | 0x80 )
 
 
 SPI_HandleTypeDef hspi1;
 
 
 struct __attribute__((packed)) var_max31865
  {
   uint16_t rtd_res_raw;            // RTD IC raw resistance register
   uint8_t  status;                 // RTD status - full status code
   uint8_t  conf_reg;               // Configuration register readout
   uint16_t  HFT_val;               // High fault threshold register readout
   uint16_t  LFT_val;               // Low fault threshold register readout
   };
 
  struct var_max31865 rtd_data;
  uint8_t read_addr = 0x00; //Read address of Configuration register
  double Temperature,RTD;
  void MAX31865_full_read(void)
  {
  uint8_t read_data[8]; //variable to store the contents of the registers
  uint8_t i = 0; //loop variable
  CS_ENABLE
  HAL_SPI_Transmit(&hspi1, &read_addr, 1, TIMEOUT_VAL);
  for(i = 0; i < 8; i++)
    {
    HAL_SPI_Receive(&hspi1, &read_data[i], 1, TIMEOUT_VAL);
    }
 
   //   HAL_Delay(10);
   CS_DISABLE
   rtd_data.conf_reg = read_data[0]; //Store config reg data
   rtd_data.rtd_res_raw = ((read_data[1] << 8) | read_data[2]) >> 1; 
   rtd_data.HFT_val = ((read_data[3] << 8) | read_data[4]) >> 1; 
   rtd_data.LFT_val = (read_data[5] << 8) | read_data[6]; 
   rtd_data.status = read_data[7]; //Store fault status reg data    
    }
 
  int main(void)
   {
 
  uint8_t config_reg_write[] = {WR(REG_CONFIG), 0xC2}; //( 0x80 ,0xC2)
  //char Rrtd[30]; //array to print RTD resistance
  //char Trtd[30]; //array to print RTD temperature
  HAL_Init();
  /* Configure the system clock */
  SystemClock_Config();
  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_SPI1_Init();
  CS_ENABLE
  HAL_Delay(10); 
  HAL_SPI_Transmit(&hspi1, &config_reg_write[0], 1, TIMEOUT_VAL);
  HAL_SPI_Transmit(&hspi1, &config_reg_write[1], 1, TIMEOUT_VAL);
  CS_DISABLE
  HAL_Delay(100);
  while (1)
  {
  HAL_Delay(500);
  MAX31865_full_read();
  RTD = ((double)rtd_data.rtd_res_raw * 4700) / 32768; 
  HAL_Delay(2000);
  Temperature = ((double)rtd_data.rtd_res_raw / 32) - 256;
  // sprintf(Trtd, "Trtd = %lf deg C\n", tmp);
  // HAL_UART_Transmit(&huart2, (uint8_t *)Trtd, 30, TIMEOUT_VAL); 
  HAL_Delay(2000);  }
  }