Any suggestion to interface 5V to 3.3V signal

convert 5v to 3.3 v

This could also work. Limitation: speed under 1Mbit, and pull_up conssumption. You can trade off this depending on the size of the pull-up.
HCT125 has 4 of this buffers, but you can get same design with "only 1 gate" chips from p h i l li p s, f a i r c h i l d, t e x a s...
Hope this helps

convert 5v analog to 3.3v

dinosaur said:

Hi All,

Any one can suggest a simple circuit technique or component solution to do the following signaling requirement:

1. 5V signal will be level-shift to 3.3V
2. 3.3V signal will pass-thru directly without attentuation.

Thanks.

Click to expand...

This simple circuit will do what you requested, you only need one resistor and one diode.

1. 5V signal will be level-shifted to 3.3V
2. 3.3V signal will pass-thru directly without attentuation.

When the signal in goes low the output goes low (signal out will be signal in plus the diode forward voltage). If you want a low forward voltage you should use a schottky diode, but a standard diode can be used in most cases.
When signal in goes high (3.3V or 5V) the diode will be reverse biased and signal out will be pulled high (3.3V) thru the resistor.

You can also use this circuit as an 5V tolerant AND-gate if you connect additional diodes to other input lines like this:

5v 3.3v voltage divider

hi friend

I think the best solution is MC14504B, it provides some good feature's

https://www.onsemi.com/pub/Collateral/MC14504B-D.PDF

simple 5v to 3.3v logic

There are three solutions
1- Use one of 74LVC series which produced by many companies as IDT, Philips, Texas, ...etc.

2- Use two cascaded inverters where the input is the 5V signal and there collector pulled to 3.3V.

3- the following described circuit is bidirectional one.

two bipolar thransistor connected as follows
a) the bases are connected togetrher and connected to fixed 3.3V
b) the emmiter of Q1 connected to collector to Q2 and vis versa
c) oneof the emmiter-collector pair pulled to 5V and the other to 3.3V
by simple analysis if for example 5V signal pulled to GND on of the transistors will on workin as simple inveret to the 3.3V base signal and the output on 3.3V side will go to GND and similar to the other side.

convert 5v 3.3v

4053 can also be used 8)

5v to 3.3v voltage divider

Two Transistors Form Bidirectional Level Translator:
http://www.hagtech.com/pdf/translator.pdf

Interfacing the 3-volt DataFlash with a 5-volt System:
http://www.atmel.com/dyn/resources/prod_documents/dataflash.pdf

convert 5v to 3.3v

You can try this.

ST2378E
Bidirectional ±15kV High Speed Level Translator

http://www.stm.com/stonline/books/pdf/docs/9489.pdf

Regards!

3.3 v to 5v conversion

If speed is not very high,Pls use R to divide.
If it need high speed,you can use high speed open drain logic device,then use pull-up resistor to 3.3V.
you also use transistor or mos to converter,use 3.3V to power transistor or mos.

convert 3.3v into 5v

Use voltage divider(resistors) is the most method which used by Intel

interfacing 5v 3.3 v

I want level shifter for connecting 5V SIMM to 3.3 V SIM interface

5v 3.3v conversion

check lv4245 an deratives :



https://www.fairchildsemi.com/products/logic/translators/translator.html

interfacing 3.3v to 5v

sehonkit wrote
5V i/o
/
\
/ 2K
\
|
--------- 3.3V i/o
/
\
/ 3K
\
|
GND

if the load between vcc and ground are not same tha's would be some diffrent voltage divider will out

3.3 v 5v conversion

use M14504B

3.3 v to 5v converter

Use NC7SZ125

3.3 v 5v converter

74LCX16652 is OK for you

how to convert 5v to 3.3v

The best conversion

Using Zener Diode 3.3V

convert 3.3 v to 5v

I strongly recommend 74HC4050. works downto 1.9V and upto 15V...

5v to 3v3 converter

Selecting the Right Level-Translation Solution

https://focus.ti.com/lit/an/scea035a/scea035a.pdf



MAX3372E, MAX3373E, MAX3374E, MAX3375E, MAX3376E, MAX3377E, MAX3378E, MAX3379E, MAX3390E, MAX3391E, MAX3392E, MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad Low-Voltage Level Translators in UCSP

World's Smallest Level Translator
The MAX3372E-MAX3379E and MAX3390E-MAX3393E ±15kV ESD-protected level translators provide the level shifting necessary to allow data transfer in a multivoltage system. Externally applied voltages, VCC and VL, set the logic levels on either side of the device. A low-voltage logic signal present on the VL side of the device appears as a high-voltage logic signal on the VCC side of the device, and vice-versa. The MAX3374E/MAX3375E/ MAX3376E/MAX3379E and MAX3390E-MAX3393E unidirectional level translators level shift data in one direction (VL —VCC or VCC —VL) on any single data line. The MAX3372E/MAX3373E and MAX3377E/MAX3378E bidirectional level translators utilize a transmission-gate-based design (Figure 2) to allow data translation in either direction (VL ´ VCC) on any single data line. The MAX3372E-MAX3379E and MAX3390E-MAX3393E accept VL from +1.2V to +5.5V and VCC from +1.65V to +5.5V, making them ideal for data transfer between low-voltage ASICs/PLDs and higher voltage systems.
All devices in the MAX3372E-MAX3379E, MAX3390E- MAX3393E family feature a three-state output mode that reduces supply current to less than 1µA, thermal short-circuit protection, and ±15kV ESD protection on the VCC side for greater protection in applications that route signals externally. The MAX3372E/MAX3377E operate at a guaranteed data rate of 230kbps. Slew-rate limiting reduces EMI emissions in all 230kbps devices. The MAX3373E-MAX3376E/MAX3378E/MAX3379E and MAX3390E-MAX3393E operate at a guaranteed data rate of 8Mbps over the entire specified operating voltage range. Within specific voltage domains, higher data rates are possible. (See Timing Characteristics.)

The MAX3372E-MAX3376E are dual level shifters available in 3 x 3 UCSP™ and 8-pin SOT23-8 packages. The MAX3377E/MAX3378E/MAX3379E and MAX3390E-MAX3393E are quad level shifters available in 3 x 4 UCSP and 14-pin TSSOP packages.

3v3 5v converter

SN74LVCC4245 from TI, look for SLAA148 this paper has this title:
Interfacing the 3V MSP430 to 5V circuits

leomecma

5v to 3.3v io conversion

i can suggest u one option as using a switcher ic from texas tps54310 using which u can convert 5v to 3.3v
but this goes like simple operation and a complex ckt, so first u decide from where u r taking the 5v and the where will u feed 3.3v if it is going to any processor or other then u can try this.
U canget more details from its data sheet and even texas supports with samples u can even rig the cke if u have some resistances and capacitors

**broken link removed**