Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

+40V 0v -40v / 10A SMPS For Power Amplifier

Status
Not open for further replies.
Hi Deepone
greetinks thanks for reply any idea what is value of preset and transistor numbers i want to try everything
warm regards
andrew lebon
 

Attachments

  • IR21531 Circuit.png
    IR21531 Circuit.png
    57.3 KB · Views: 362

Greeting.
Certainly you can sure themselves but such scheme probably blast. ir2153 switching off it is necessary to do quickly and once.
 
Hi Deepone
greetings can i use igbts in my smps now is it possible
warm regards
andrew lebon

- - - Updated - - -

Hi Deepone
greetings can i use igbts in my smps now is it possible
warm regards
andrew lebon

- - - Updated - - -

Hi Deepone
greetings can i use igbts in my smps now is it possible
warm regards
andrew lebon

- - - Updated - - -

Hi Deepone
greetings trying to make pcb for your wonderful smps
warm regards
andrew lebon
 

Attachments

  • JPG.jpg
    JPG.jpg
    190.8 KB · Views: 638
Hi Deepone
greetings can i remove all 4 IRFP460 AND REPLACE WITH IGBT IRG4PF50W are they ok to use i use freewheeling diodes
warm regards
andrew
 

can i remove all 4 IRFP460 AND REPLACE WITH IGBT IRG4PF50W
Click to expand...
yes, you can ). One IRG4PF50W instead of two IRFP460.
ok to use i use freewheeling diodes
Click to expand...
yes, they are ok. Or possible use IGBT with "D" index, like IRG4PC50UD, IRG4PF50WD.
 

Deepone And Andrew Many Thanx i'm about to finish and testDSC00954.JPGDSC00955.JPGDSC00956.JPG

Deepone If i use IGBT with build in diode do i still need to put those 1.5ke440 's?

what is the oscillation freq of 2153 using 3.3k and 4700pf on pin 3 and 4

i use 3.3k and 4700pf main Core primary inductance 2.5mh(core T50,ee55,ETD59) is this correct sir Deepone?
 
Last edited:

Hi, Irvynejay.
do i still need to put those 1.5ke440 's?
Click to expand...
If used 900V IGBT like IRG4PF50W that it is not necessary (but 900V IGBT will 30% more heat then 600V IGBT).
In general for half-bridge converter even with 600V keys these TVS is not obligatory components.
what is the oscillation freq of 2153 using 3.3k and 4700pf
Click to expand...
As judged by datasheet frequency must be around 42 kHz.

Core primary inductance 2.5mh(core T50,ee55,ETD59) is this correct
Click to expand...
I think for half-bridge topology primary inductance must be in 700 - 1000 uH interval. 2,5mH more suits for full bridge.
 

Hello Irvynejay
greetings NICE to see you make this smps
warm regards
andrew lebon
 

Hi Andrew Lebon,
I also want to make an smps of 2KW rating , so please specify which circuit did you use.
 
post#14 and post#48 used to make smps
Hi Picgak
greetings combination of both above mentioned post used to make smps FOR totem trs use BD139 BD140
WARM REGARDS
andrew lebon
 

Hi Deepone
greetings can this ocp be used for ir 2153 smps using current sensing trafo 1:100 turn ratio
warm regards
andrew lebon:idea:

- - - Updated - - -

Hi Deepone
greetings can this ocp be used for ir 2153 smps using current sensing trafo 1:100 turn ratio
warm regards
andrew lebon:idea:
 

Attachments

  • OCP.JPG
    OCP.JPG
    224.4 KB · Views: 147
  • OCP.JPG
    OCP.JPG
    224.4 KB · Views: 151

greetings can this ocp be used for ir 2153 smps using current sensing trafo 1:100 turn ratio
Click to expand...
Hi Andrew
For my opinion you can also use a low value resistor to sense current through the primary of your transformer and then limit it as well .
Best Wishes
Goldsmith
 
Andrew Lebon ,
From your pcb I think you have removed the triac part of the schematic and used a relay . Is it timer operated or according to the charge on the input cap
regards ani
 

@Picgak triac sofstart is replace with relay type softstart
 

softstart used from this circuit
 

Attachments

  • 3fca3573fea22cd7.jpg
    3fca3573fea22cd7.jpg
    347.9 KB · Views: 238

I have done audio amplifier (based on LME49830) with such power source too. Quite well, sound loud and clean.
 
Last edited:

hello deepone sir

Deepone sir Many Many Thanx i'm about to finish and test this smps



warm regards
sameerx1

- - - Updated - - -

http://www.youtube.com/watch?v=Kugbq_qw7A0&feature=youtu.be
 

Attachments

  • DSCN3942.jpg
    DSCN3942.jpg
    271.7 KB · Views: 151
  • DSCN3943.jpg
    DSCN3943.jpg
    991 KB · Views: 159
  • DSCN3939.jpg
    DSCN3939.jpg
    263.4 KB · Views: 132

hi deepone , can u tell me this scematic is correct?vithout viper?
 

Attachments

  • deepone smps correct edit without viper.gif
    deepone smps correct edit without viper.gif
    34 KB · Views: 201
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top