Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by vetriselvan

  1. V

    Output of crystal oscillator.

    Hi all, Thanks a lot for your support to me. Regards Vetri.
  2. V

    Output of crystal oscillator.

    Dear keith, I forgot the part no of the oscillator which i have tested.So i searched the new oscillator from DIGIKEY and the part no is CTX753-ND.the data sheet also attached above.So please let me know whether the above part no will give the square wave.
  3. V

    Output of crystal oscillator.

    Dear all, Finally shall i use the part no in the datasheet.Plz suggest.
  4. V

    Output of crystal oscillator.

    Dear keith, Hereby i have attached one datasheet.Please check and let me know whether the attached datasheet part no will provide the 10Mhz square wave with 5V. DIGIKEY PART NO:CTX753-ND Regards Vetri
  5. V

    Output of crystal oscillator.

    Der keith, I forgot the part no & Make..I will reply you soon once i got it.I have checked with Textronics 200Mhz scope. Regards Vetri.
  6. V

    Output of crystal oscillator.

    Thank you keith... But i have tested one normal CXO.But it produced the sine wave.So only i have doubt in these..pls clarify... Regards Vetri.
  7. V

    Output of crystal oscillator.

    Dear Keith, Thanks for ur post. I need 10Mhz square wave from the crystal oscillator with 5V. My doubt is shall i use the normal CXO or VCXO(voltage controlled oscillator). Regards Vetri
  8. V

    Output of crystal oscillator.

    Dear all, What is the output of the crystal oscillator.Is it sine or square wave.Then what is difference between CXO,VCXO,OCXo,TCXO. Regards Vetriselvan
  9. V

    Need help on ADC design

    yaeh..Ok..thanks for your help.
  10. V

    230VAC to 12VDc converter circuit

    Hi, I think transformer is better one of this conversion..
  11. V

    Need help on ADC design

    Ya..i am going to use micro controller next to ADC.But i need help on to select the ADC part no based on interfaces,resolution & sampling rates.Also i need your comments on the above attached schematics.
  12. V

    Need help on ADC design

    Hi Thoma, Please find the below attachment for your reference.In that i have used parallel ADC with only one channel.. My requirement is i need to connect max 8 channels from Diff.amp to ADC.So i need help to choose the ADC,interfaces & resolutions. Vetri
  13. V

    Need help on ADC design

    Hi, I dont need to physically build the ADC.i need to interface the ADC with micro controller.For that i need help to choose the ADC interface,No.of bits,sampling rates. I need to connect maximum of 8 channels with ADC.
  14. V

    Need help on ADC design

    Hi, My input to diff amp is 2V and 1V Dc supply.and the output from the diff amp is 0-5V.This output going to ADC.My requirement is 12 bit parallel or serial ADC.Can someone help me to choose the ADC and provide me the full schematic of both diff amp and ADC. Regards Vetri
  15. V

    need help on Mosfet design suggestions

    Hi venky , I think for driving 3A load compare to resistance value,the resistance watt is very important.
See more

Part and Inventory Search

Back
Top