Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by venkateshjuturu

  1. V

    Fatal Error in Tanner Spice

    here i am attaching two images, one image shows code and the other shows fatal error my problem is i want to print a exponential current pulse in tanner spice with Tr=50ps, Tf=164ps please any one can help me in solving this problem thanks in advance
  2. V

    Device noise simulation

    thanks for your reply i got noise factor for a nmos device as 3k dB in cadence using 2 port (sp) analysis whether it is correct or not but i need to know how to calculate the device noise using Tanner Spice using spice netlist please help in this regard
  3. V

    Noise analysis using INA129 pspice model

    hai, i am using T- spice simulator can u please explain step by step for calculating device noise and which parameters i have to include in the spice netlist i am using ptm models 32nm sub-circuit model for FinFET (double-gate): V0.0 hope u will reply to me thanks in advance
  4. V

    Device noise simulation

    hai, i am using T- spice simulator can u please explain step by step for calculating device noise especially where i can get these values the noise values for active devices are included in their models and should appear when you perform a noise analysis of the circuit. i am using ptm models...
  5. V

    how to plot frequency vs voltage control for vco in tanner spice

    thank you man
  6. V

    how to find power spectrum using Tanner Spice

    Sir, I am using TannerToolsV15.00 for my project to simulate VCO circuit may i know how to calculate power spectrum i.e power Vs Frequency plot using either W Edit or any spice command for plotting, which is helpful to me one more thing in one paper they said like VCO draws only 315uA average...
  7. V

    can we design LC VCO circuit using Sentaurus TCAD

    thank you erikl
  8. V

    can we design LC VCO circuit using Sentaurus TCAD

    thank you very much erikl can i know how to calculate phase noise using SPICE help me in this regard
  9. V

    how to calculate tuning range for vco

    can you elaborate how to calculate varicap diode cap and you mentioned from the above make it little bit clear thanks
  10. V

    [SOLVED] how to plot vco frquency with variation of control voltage

    Re: solved: how to plot vco frquency with variation of control voltage may i know the type of inductor you used in the topology and which version of cadence is it is thanks in advance
  11. V

    how to plot frequency vs voltage control for vco in tanner spice

    hai how to plot frequency vs voltage control for vco in tanner spice thanks in advance
  12. V

    can we design LC VCO circuit using Sentaurus TCAD

    hai can we design LC VCO circuit using Sentaurus TCAD and can analyze center freq, tuning range, phase noise, power consumption thanks in advance
  13. V

    Tuning range calculation of VCO in percentage?

    Re: Tuning range calculation of VCO hai, may i know how u got tuning from 2.25Ghz to 2.63 and variation in capacitance i mean how to cal capacitance vs voltage using Tanner spice thanks in advance
  14. V

    how to calculate tuning range for vco

    hai may i know how to find tuning range for LCvco and center frequency is 1/(2*pi*(LC)^(1/2)) thanks in advance
  15. V

    How to simulate the Kvco with spectre?

    please can you elaborate what you said i am not getting thank you
See more

Part and Inventory Search

Back
Top