Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi,
I need Schematic Diagram of Samsung Sync Master 740NW LCD Monitor . If anyone have this schematic diagram of this Model then please share with me . Thanks in Advance .
Hi,
I need a Leadman (POWMAX) LP6100 Schematic diagram . This PSU has the problem in primary section of both MJE13007 . After repairing the Primary section this PSU is running automatically when I attach power cord with it !!! It doesn't need to be switch !! I have checked the controller section...
It seems to be a SMD based Circuit . My suggestion - don't try to repair this kind of SMD based Power supply circuit . This SMD Based circuit will ***** your brain and you will not found the parts easily .
I am also looking for a diagram of Bestec power supply which is also 4 photocouplers like...
No dude , It does not work . :sad: The same Result with 2SC5027.:sad: Then I thought that - it is the problem of Inductance of Transformer . So, I changed the Transformer also . But nothing work .
What should I do now ??
Thanks for your helpful tips . My own power supply has a 2SC5027 transistor in +5VSB unit which is now connected with my PC . Let me few hours to check with it . I will inform the result few hours later .
Thanks
No, that is not . I just shared my practical knowledge with you as you can help me properly to solve the problem - not more than that . May be you are getting angry !! I could not express myself due to my poor English - sorry for that .
Most of the ATX PSU uses 2SC3150 or 2SC3866 or 2SC5027 transistors for +5VSB Primary Section . Look at those three transistors data sheet - they all have Vce is 800V . But if you work in ATX PSU then you will see that Collector is Actually crossing 1000V, may be it is 1500V to 2000V !!! I think...
Hi,
All the single Parts of this +5VSB unit is OK . But this SMPS is not turning on . In the Red circle of the Transformer will be 1000V but it is showing 320V . Why there 1000V is not coming there ? Why the SMPS is not turning on ? What's the problem there ?? I have attached the schematic below...
Hi,
I get a ATX PSU 450W for Repairing one of my customer . But This PSU have all parts OK . I am getting 5V PS-ON and 5VSB . The Power Supply is not running . But this PSU is Running - When I make short Pin 4 of TL494 with GND and this time I do not need to short PS-ON with Ground . Just Short...
I have changed all those capacitors, Diodes and Transistor with new one . But still the Power supply is not running . What will I do now ??
Please Response ........... I am waiting for your reply ......
Oooops !! I said it before - I am not a student of Electronics . I don't know so much theory like you . I am just a practical Electronics worker . I have just share my Practical experience - that's all .
Why your PC running with Partial Load But Not running with Full Load/Suddenly damaged - May...
I have checked Q4 and Q5 C945 - Both of them are Fine . C9/C10 are 2.2μF/50V - this capacitors seems to be OK . Will I change it though ?? There is no R7 and R11 Resistor . They have only one fusing Resistor 10Ω Which is in Transistor's Base R6 and R10 . But they have used two signal/Crystal...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.